Hubbardton Forge 365615 User Manual

Installation Instructions A197

For Outdoor Chain Hung Fixture 36-5615 & 36-5615F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install Fixture (Figure 1)

Component Parts

A Lock Nut
B Crossbar
C Threaded Stud (2)
D Nipple
E Wood Screws (4)
F Canopy
G Canopy Loop
H Cover Plate
I Knurl Ball (2)

J Chain
K Fixture Loop
L Fixture Top
M Retaining Ring (2) (“F” version has only 1

retaining ring)
N 8-32 x 3/8” Screws (3)
O 8-32 x 1” Screws (3)
P Spider Assembly
Q Washer

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Remove glass retaining rings (M) and put aside and save for later use.

3. Loosen screws (O) that are shipped installed in threaded bosses on underside of

fixture next to socket and remove washer (Q) by turning clockwise to slip over
heads of screws. Loosen screws until there are only a couple threads engaged
with the threaded bosses.

4. Loosen screws (N) so that spider assembly (P) will turn clock wise. It is not

necessary to completely remove screws (N) from fixture. Once spider assembly
(P) is loose turn until it slips over the heads of the screws. Set aside for later use
(Figure 2).

5. Thread studs (C) through appropriate holes in crossbar (B) to match holes in

canopy (F).

6. Thread canopy loop (G) onto nipple (D).

7. Thread the nipple (D) into the crossbar (B) and secure with lock nut (A).

8. Attach one end of the chain to the fixture loop (K). Lace the wire through

every other link of the chain (J) to the end.

9. Slide cover plate (H) and canopy (F) over chain (J) until they rest against

fixture top (L).

10. Fasten the chain to the canopy loop (G) and slip wires through the canopy

loop (G) and nipple (D). Make sure to provide enough slack in the wire to
ensure weight of fixture is supported by the chain.

11. Raise fixture to ceiling and using at least two wood screws (E) attach cross

bar (B) to a structural member in the ceiling, centering the crossbar over the
outlet box. We've supplied wood screws with your fixture; however, different
materials and/or construction methods may require different fasteners. If in doubt,
contact a qualified electrician. Do not attach crossbar directly to outlet box.

(Figure 1)

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22646

Installation Instructions A197

For Outdoor Chain Hung Fixture 36-5615 & 36-5615F Page 2 of 2

12. Using suitable wire connectors (not provided) connect fixture wires to supply

wires (white to ribbed side of the fixture cord, black to smooth side). Connect all
ground wires to crossbar using ground screw.

connectors are twisted on securely, and no bare wire is exposed.

13. Slide canopy (F) and cover plate (H) over threaded studs (C) and push firmly to

ceiling, making sure that no wires are pinched between fixture canopy and ceiling.
Fasten with knurled balls (I). Be sure studs (C) are fully seated in the knurled
balls (I).

14. Install glass (see instructions below).

To Install Outer Glass (Figure 3)

Component Parts

N 8-32 x 3/8” Screws (3)
P Spider Assembly
R Socket
S Outer Glass (larger diameter glass)

1. Slip outer glass (S) over spider assembly (P).

2. Raise spider assembly (P) with outer glass (S) installed and slip over socket (R)

aligning holes in the top of the spider assembly (P) keyed ring goes over
screws (N).

3. Turn spider assembly (P) counter clockwise until it stops. Tighten three

screws (N) until snug against the spider assembly. Be careful not to over
tighten.

To Install Inner Glass (Figure 4)

Caution: Make sure wire

(Figure 3)

Component Parts

M Retaining Ring
Q Washer
T Inner Glass

1. Raise inner glass (T) and washer (Q) over socket aligning holes in washer (Q)

so the washer keyed ring goes over screws.

2. Turn washer (Q) counter clockwise until it stops. Tighten three screws until

snug against the inside of glass (T). Be careful not to over tighten.

3. Thread the first retaining ring (M) on to socket until it is against washer (Q).

4. Thread the second retaining ring (M) onto socket until it is snug against the

first retaining ring. Do not over tighten. Disregard this step for the “F”
version.

5. Install light bulb. “F” version bulb is included.

6. Restore electricity at the main breaker.

If you need further assistance, or find that you are missing any parts, please contact

(Figure 4)

the dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22646