Page 1
Installation Instructions A192
For Meridian Chain-Hung Fixture 36-5610 & 36-5610F Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Install Fixture (Figure 1)
Component Parts
A Lock Nut
B Crossbar
C Cupped Washer
D Ground Screw
E Threaded Stud (2)
F Nipple
G Wood Screws (4)
Caution: Be sure power is off at the main breaker box prior to installation
1. Carefully unpack the fixture from the carton.
2. Thread studs (E) through appropriate holes in crossbar (B) to match
holes in canopy (H).
3. Thread the nipple (F) into the crossbar (B) and secure with lock nut (A).
4. Thread canopy loop (I) onto nipple (F).
5. Attach one end of the chain (L) to the fixture loop (M). Lace the wire
through every other link of the chain (L) to the end.
6. Slide cover plate (J) and canopy (H) over chain (L) until they rest
against fixture top (N).
7. Fasten the chain (L) to the canopy loop (I) and slip wires through the
canopy loop (I) and nipple (F). Make sure to provide enough slack in
the wire to ensure weight of fixture is supported by the chain.
8. Raise fixture to ceiling and using at least two wood screws (G) attach
cross bar (B) to a structural member in the ceiling, centering the
crossbar over the outlet box. We've supplied wood screws with your
fixture; however, different materials and/or construction methods may
require different fasteners. If in doubt, contact a qualified electrician. Do
not attach crossbar directly to outlet box.
9. Using suitable wire connectors (not provided) connect fixture wires to
supply wires (white to ribbed side of the fixture cord, black to smooth
side). Connect all ground wires to cupped washer (C) and ground screw
(D).
Caution: Make sure wire connectors are twisted on securely, and
no bare wire is exposed.
10. Slide canopy (H) and cover plate (J) over threaded studs (E) and push
firmly to ceiling, making sure that no wires are pinched between fixture
canopy and ceiling. Fasten with knurled balls (K). Be sure studs (E) are
fully seated in the knurled balls (K).
11. Install glass (see instructions on next page).
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
H Canopy
I Canopy Loop
J Cover Plate
K Knurl Ball (2)
L Chain
M Fixture Loop
N Fixture Top
(Figure 1)
(continued)
22418
Page 2
Installation Instructions A192
For Meridian Chain-Hung Fixture 36-5610 & 36-5610F Page 2 of 2
To Install Outer Glass (Figure 2)
Component Parts
O Screws (3)
P Retaining Ring (2)
Q Socket
R Outer Glass (larger diameter glass)
S Spider Assembly
1. Remove glass retaining rings (P) and put aside and save for later use.
2. Unthread screws (O) that are shipped installed in threaded bosses on underside
of fixture next to socket (Q). Loosen screws until there are only a couple
threads engaged with the threaded bosses.
3. Slip outer glass (R) over spider assembly (S).
4. Raise spider assembly (S) with outer glass (R) installed and slip over socket
(Q) aligning holes in the top of the spider assembly (S) keyed ring goes over
screws (O).
5. Turn spider assembly (S) counter clockwise until it stops. Tighten three
screws (O) until snug against the spider assembly. Be careful not to over
tighten.
To Install Inner Glass
Component Parts
P Retaining Ring (2)
T Inner Glass
(Figure 3)
1. Slip inner glass (T) over socket.
2. Thread the first retaining ring (P) onto socket until it is against top of the
inner glass (T).
3. Thread the second retaining ring (P) onto socket until it is snug against the
first retaining ring. Do not over tighten.
4. Install light bulb. âFâ version bulb is included.
5. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact
the dealer from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper
installation, lamping or use of this fixture.
(Figure 2)
(Figure 3)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22418
Loading...