Hubbardton Forge 365605 User Manual

Installation Instructions A191

(Fig

2

)

For Outdoor Semi-Flush 36-5605 & 36-5605F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

To Install Fixture (Figure 1)

Component Parts

A Crossbar
B Ground Screw
C Threaded Stud (2)
D Canopy
E Barrel Knobs (2)
F Glass Retaining Ring (2)

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Thread studs (C) through appropriate holes in cross bar (A) to match

hole centers in canopy (D). Move ground screw (B) to another
available threaded hole if necessary.

3. Using two machine screws (not provided) fasten cross bar (A) to the

electric box using outer oval holes to orient fixture to desired hanging
position.

an existing fixture, retain the screws for use with the new fixture.

Note: A new electric box comes with screws. When replacing

5. Using suitable wire connectors (not provided) connect fixture wires to supply

wires (white to white or ribbed and black to black or smooth). Connect all
ground wires to green ground screw (B).

are twisted on securely, and no bare wire is exposed.

Caution: Make sure wire connectors

6. Slide fixture canopy (D) over threaded studs and push firmly to ceiling, making

sure that no wires are pinched between fixture canopy and ceiling. Fasten with
barrel knobs (E). Be sure studs (C) are fully seated in the barrel knobs (E).

7. Remove glass retaining ring (F) and save for later use.

8. Refer to instructions below to install glass & bulb.

(Figure 1)

To Install Outer Glass

Component Parts

G Screws (3)
H Socket
I Outer Glass (larger diameter glass)
J Spider Assembly

(Figure 2)

1. Unthread screws (G) that are shipped installed in threaded bosses on underside

of fixture next to socket (H). Loosen screws until there are only a couple
threads engaged with the threaded bosses.

ure

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 21174

Installation Instructions A191

(Fig

3

)

For Outdoor Semi-Flush 36-5605 & 36-5605F Page 2 of 2

2. Slip outer glass (I) over spider assembly (J).

3. Raise spider assembly (J) with outer glass (I) installed and slip over socket (H) aligning holes in the top of the

spider assembly (J) keyed ring goes over screws (G).

4. Turn spider assembly (J) counter clockwise until it stops. Tighten three screws (G) until snug against the spider

assembly. Be careful not to over tighten.

To Install Inner Glass

Component Parts

F Glass Retaining Ring (2)
K Inner Glass

1. Slip inner glass (K) over socket.

2. Thread the first retaining ring (F) onto socket until it is against top of the inner

glass (K).

3. Thread the second retaining ring (F) onto socket until it is snug against the first

retaining ring. Do not over tighten.

4. Install light bulb. “F” version bulb is included.

5. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 3)

ure

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735 21174