Page 1
Installation Instructions B271
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
Ethos Sconce 308010D & 308015D Page 1 of 2
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or
electrician.
To Mount Fixture to Wall (Figures 1 & 2)
Component Parts
Caution: Be sure power is off at the main breaker box prior to installation.
A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (2)
F Rubber Washer (2)
G Green Ground Screw
H Cupped Washer
I Caulking Lip
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (B) over the
electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on
the wall behind.
IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box and/or a framing member in at least two locations. Do not
depend on drywall anchors alone to support this fixture. If in doubt, contact a qualified e l ec tr ic ian.
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using
a light weight hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the
bracket into position. Using two machine screws (not provided), fasten the wall mount bracket (B) to the
electric box making sure that the bracket is level. Using the #10 screws (D), screw the bracket securely to
the wall. Be careful not to over-tighten or strip the anchors.
NOTE: A new electrical box comes with screws. When replacing a fixture, retain the existing screws for
use with the new fixture.
4. Hold the fixture assembly (A) close to the wall mount brack et and using suita ble wire conne cto rs (no t
provided), connect fixture wires to supply wires (white to white or ribbed and black to black or smooth).
Ground the mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail
lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27720 A
Page 2
Installation Instructions B271
(Figure 3)
(Figure 2)
Ethos Sconce 308010D & 308015D Page 2 of 2
5. Apply a generous bead of a suitable caulking material to caulking lip (I) on the
fixture (not provided) (Figure 2).
6. Carefully tuck all wires behind the fixture assembly and inside the wall mount
bracket and place the fixture firmly onto bracket (B) and fasten with #8 black
screw (E) and rubber washer (F) on top.
7. Install 2
bracket (B).
To Install Glass (Figure 3)
Component Parts
A Fixture Assembly
J Decorative Glass
K Glass Diffuser
L Top Bracket
M Set Screw (3)
N Plastic Bumper
1. Set Screws (M) are shipped installed in the fixture. Prior to glass installation,
ensure that all set screws (M) are unscrewed enough to allow installation of glass.
2. Slide glass diffuser (K) down into the fixture from the top. Diffuser should be
seated in the bottom bracket.
3. Tighten set screw (M) in bottom bracket against glass diffuser (K). Do not
over tighten.
4. If desired, the plastic bumper (N) can be adhered to the top of the decorative
glass (J).
5. Slide decorative glass (J) down into the fixture from the top. Decorative glass
should be seated in the bottom bracket.
6. Slide top bracket (L) into the fixture. Check fit between set screw (M) in top
bracket (L) and glass diffuser (K). Adjust Set Screw as necessary to contact
glass diffuser (K). Note: Removal of Top Bracket is necessary to adjust Set
Screw. Once top bracket is seated in fix ture, ag ains t the glass, t ighten the set
screw (M) in fixture (A) against top bracket (L).
7. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact
the dealer from which you purchased this product. We hope you enjoy your fixtur e!
Hubbardton Forge will not be liable for injury or damage caused by improper
*
installation, lamping or use of this fixture.
nd
black screw (E) in bottom of fixture attaching to wall mounting
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27720 A
Loading...