
Installation Instructions B142
For Medium and Large After Hours Outdoor 30-7860, 30-7860F, 30-7861 & 30-7861F Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Adjust Top Plate
Component Parts
A 8-32 x 1/4" Screw Top Plate
B Top Plate
C Glass
D Bracket
E 8-32 x 3/8” Screw (2)
F Fixture
(Figure 1)
1. Carefully unpack the fixture from the carton.
2. Slide glass (C) into fixture (F).
3. Slip top plate (B) onto fixture (F) until it rests on top of glass (C).
4. Loosen screws in bracket (D).
5. Remove screw (A) from bracket (D) and set aside for later use.
6. Raise or lower bracket (D) as needed until it touches top plate (B) and tighten
screw (E).
7. Slip 8-32 x 1/4" screw (A) through top plate (B) and thread in to bracket (D) and
tighten (be careful not to over tighten).
8. Remove screw (A), top plate (B) and glass (C) and set to the side temporarily.
9. Continue with installation instructions below.
(Figure 1)
To Install Fixture to Wall
Component Parts
F Fixture
G Mounting Bracket
H 8-32 x 1” Screw (2)
I Caulking Lip
Caution: Be sure power is off at the main breaker box prior to installation.
(Figures 2 & 3)
1. Using two machine screws (not provided) attach mounting bracket (G) to the
electric box using inside oval holes to orient fixture.
comes with screws. When replacing a fixture, retain the screws for use with
the new fixture.
Note: A new electric box
2. Using suitable wire connectors (not provided), connect the fixture wires to the
supply wires, (white to white, black to black, bare copper or green to bare
copper or green). If the fixture is wired with twin lead lamp cord, connect the
ribbed side to white, and the smooth side to black.
connectors are twisted on securely and no bare wires are exposed.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
Caution: Make sure wire
(Figure 2)
(continued)
21193

Installation Instructions B142
For Medium and Large After Hours Outdoor 30-7860, 30-7860F, 30-7861 & 30-7861F Page 2 of 2
4. Apply a generous bead of a suitable caulking material to caulking lip (I)
on the fixture (Figure 3).
5. Carefully tuck all wires behind the fixture, place fixture firmly against the wall
and fasten with 8-32 x 1 5/8" screws (H). To ensure a water tight seal, apply a thin
bead of caulking around entire perimeter of the fixture.
6. Install light bulb.
To Install Glass
Component Parts
A 8-32 x 1/4" Screw
B Top Plate
C Glass
D Bracket
F Fixture
(Figure 4)
(Figure 3)
1. Slide glass (C) into fixture (F).
2. Slip top plate (B) onto fixture (F) until it rests on top of glass (C).
3. Slip 8-32 x 1/4" screw (A) through top plate (B) and thread into bracket (D) and
tighten. (Be careful not to over tighten)
(Figure 4)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21193