Page 1
Installation Instructions B137
For Small After Hours Outdoor 30-7858 & 30-7858F Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
To Adjust Top Plate (Figure 1)
Component Parts
A 8-32 x 1/4" Screw
B Top Plate
C Glass
D Bracket
E 8-32 x 3/8” Screw
F Fixture
1. Carefully unpack the fixture from the carton.
2. Slide glass (C) into fixture (F).
3. Slip top plate (B) onto fixture (F) until it rests on top of glass (C).
4. Attach bracket (D) with 8-32 x 3/8" screw. Do not tighten at this point.
5. Raise or lower bracket (D) as needed until it touches top plate (B) and tighten
screw (E).
6. Slip 8-32 x 1/4" screw (A) through top plate (B) and thread in to bracket (D) and
tighten. Be careful not to over tighten.
7. Remove screw (A), top plate (B) and glass (C) and set to the side temporarily.
8. Continue with installation instructions below.
To Install Fixture
(Figures 2 & 3)
(Figure 1)
Component Parts
F Fixture
G Crossbar
H 8-32 x 1 5/8” Screw (2)
Caulking Lip
I
Caution: Be sure power is off at the main breaker box prior to installation.
Using two machine screws (not provided) attach cross bar (G) to the electric
1.
box using inside oval holes to orient fixture.
with screws. When replacing a fixture, retain the screws for use with the new
fixture.
Note: A new electric box comes
2. Using suitable wire connectors (not provided), connect the fixture wires to
the supply wires, (white to white, black to black, bare copper or green to bare
copper or green). If the fixture is wired with twin lead lamp cord, connect the
ribbed side to white, and the smooth side to black.
Caution: Make sure wire connectors are twisted on securely and no bare
wires are exposed.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 2)
(continued)
21167
Page 2
Installation Instructions B137
For Small After Hours Outdoor 30-7858 & 30-7858F Page 2 of 2
3. Apply a generous bead of a suitable caulking material to caulking lip (I) on the fixture
(Figure 3).
4. Carefully tuck all wires behind the fixture, place fixture firmly against the wall and
fasten with 8-32 x 1 5/8" screws (H). To ensure a water tight seal, apply a thin bead of
caulking around entire perimeter of the fixture.
5. Install light bulb (Fluorescent version bulb is included).
(Figure 3)
To Install Glass
Component Parts
A 8-32 x 1/4" Screw
B Top Plate
C Glass
D Bracket
F Fixture
(Figure 4)
1. Slide glass (C) in to fixture (F).
2. Slip top plate (B) on to fixture (F) until it rests on top of glass (C).
3. Slip 8-32 x 1/4" screw (A) through top plate (B) and thread in to bracket (D)
and tighten. Be careful not to over tighten.
If you need further assistance, or find that you are missing any parts, please contact the dealer
(Figure 4)
from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
21167
Loading...