Page 1
Installation Instructions B266
Port Outdoor Sconces 30-6565 & 30-6567 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall
Component Parts
A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (2)
F Rubber Washer (1)
G Green Ground Screw
H Cupped Washer
I Caulking Lip
Caution: Be sure power is off at the main
breaker box prior to installation.
(Figures 1 & 2)
1. Carefully unpack the fixture from the
carton.
2. Center the wall mount bracket (B)
over the electrical box being sure to
hold it plum and level. With a pencil,
mark the location of all mounting
holes in the wall mount bracket on the
wall behind.
IMPORTANT: Wall mount bracket
must be secured to a solidly mounted
electrical box and/or a framing
member in at least two locations. Do
not depend on drywall anchors alone
to support this fixture. If in doubt, contact a qualified electrician.
(Figure 1)
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail lead to the bracket
and connect all ground wires (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
5. Apply a generous bead of a suitable caulking material to calking lip (I) on the fixture (not provided) (Figure 2).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27225
Page 2
Installation Instructions B266
Port Outdoor Sconces 30-6565 & 30-6567 Page 2 of 2
6. Carefully tuck all wires behind the fixture assembly and inside the
wall mount bracket and place the fixture firmly onto bracket (B) and
fasten with #8 black screw (E) and rubber washer (F) on top.
nd
7. Install 2
mounting bracket (B).
black screw (E) in bottom of fixture attaching to wall
To Install Glass
Component Parts
A Fixture Assembly
J Socket
K Glass for 30-6565,
L Solid Diffuser for 30-6567
M Retaining Ring
N Retaining Ring Tool
1. Remove retaining ring (M) from socket (J). Retaining ring ships
installed.
2. Slip glass (K) or solid diffuser (L) depending on which product
was purchased over socket (J).
3. Thread retaining ring (M) onto socket (J) using retaining ring
tool (N) provided until snug. Do not over tighten.
4. Install bulb (not included).
(Figure 3)
(Figure 2)
(Figure 3)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
*
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27225
Loading...