Installation Instructions B253
Port Outdoor Sconces 30-6560 & 30-6563 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall
Component Parts
A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (2)
F Rubber Washer (1)
G Green Ground Screw
H Cupped Washer
I Caulking Lip
Caution: Be sure power is off at
the main breaker box prior to
installation.
(Figures 1 & 2)
1. Carefully unpack the
fixture from the carton.
2. Center the wall mount
bracket (B) over the
electrical box being sure
to hold it plum and level.
With a pencil, mark the
location of all mounting
holes in the wall mount
bracket on the wall
behind.
IMPORTANT: Wall mount
bracket must be secured
to a solidly mounted
electrical box and/or a framing member in at least two locations. Do not depend on drywall anchors alone to
support this fixture. If in doubt, contact a qualified electrician.
(Figure 1)
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26974
Installation Instructions B253
Port Outdoor Sconces 30-6560 & 30-6563 Page 2 of 2
4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (G) and
cupped washer (H) to secure a pigtail lead to the bracket and
connect all ground wires (bare copper or green to bare copper
or green).
Caution: Make sure wire connectors are twisted on securely,
and no bare wires are exposed.
5. Apply a generous bead of a suitable caulking material to
calking lip (I) on the fixture (not provided) (Figure 2).
6. Carefully tuck all wires behind the fixture assembly and inside
the wall mount bracket and place the fixture firmly onto
bracket (B) and fasten with #8 black screw (E) and rubber
washer (F) on top.
nd
7. Install 2
wall mounting bracket (B).
black screw (E) in bottom of fixture attaching to
(Figure 2)
To Install Glass
Component Parts
A Fixture Assembly
J Socket
K Glass for 30-6560,
L Solid Diffuser for 30-6563
M Retaining Ring
N Retaining Ring Tool
1. Remove retaining ring (M) from socket (J). Retaining ring ships
installed.
2. Slip glass (K) or solid diffuser (L) depending on which product was
purchased over socket (J).
3. Thread retaining ring (M) onto socket (J) using retaining ring tool
(N) provided until snug. Do not over tighten.
4. Install bulb (not included).
(Figure 3)
(Figure 3)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
*
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26974
Loading...