Hubbardton Forge 306455 User Manual

Installation Instructions B285

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL

(Figure 1)

Fuse Outdoor Sconces 306450, 306453 & 306455 Page 1 of 2

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. Sconces are to be mounted 4 feet above ground. If installing in a non-wood frame application, we
recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figures 1 & 2)

Component Parts

A Fixture Assembly
B Wall Mounting Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (4)
F Rubber Washer (2)
G Green Ground Screw
H Cupped Washer
I Caulking Lip

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (B) over

the electrical box being sure to hold it
plum and level. With a pencil, mark the
location of all mounting holes in the wall
mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must
be secured to a solidly mounted electrical
box and/or a framing member in at least
two locations. Do not depend on drywall
anchors alone to support this fixture. If in
doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (G) and cupped washer (H) to secure a pigtail lead to the bracket
and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28107

Installation Instructions B285

(Figure 3)

(Figure 2)

Fuse Outdoor Sconces 306450, 306453 & 306455 Page 2 of 2

5. Apply a generous bead of a suitable caulking material (not provided) to calking lip (I)

on the fixture. Caulk should be applied around the entire perimeter of the canopy
(Figure 2).

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket

and place the fixture firmly onto bracket (B) and fasten with two #8 black screws (E)
and rubber washers (F) on top.

7. Install the two remaining black screws (E) in bottom of fixture attaching to wall

mounting bracket (B).

To Install Glass (Figure 3)

Component Parts

A Fixture Assembly
J Inner Glass
K Outer Glass
L Socket
M Top Arm
N Hex Nut (2)
O Threaded Stud

1. Install bulb (not included).

2. Slip inner glass (J) over socket (L) until it rest in the cup.

3. Slip outer glass (K) over inner glass (J) until it rest in the larger cup.

4. Thread hex nut (N) on to threaded stud (O)

5. Place the top arm (M) down over the outer glass (K) and slip onto the threaded

stud (O).

6. Secure the top arm (M) by threading the hex nut (N) onto the threaded stud (O).

Tighten until snug.

7. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

*

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28107