Hubbardton Forge 305610 User Manual

Installation Instructions B162

For Outdoor Wall sconce 30-5610 & 30-5610F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

To Install Fixture

Component Parts

A Cross Bar
B Threaded Studs (2)
C Fixture
D Barrel Knobs (2)
E Caulking Lip
F Screws (3)
G Retaining Ring (2) (“F” version has only 1 retaining ring)
H Spider Assembly

Caution: Be sure power is off at the main breaker box prior to installation.

(Figures 1, 2 & 3)

1. Carefully unpack the fixture from the carton.

2. Remove glass retaining rings (G) and save for later use. Note – “F”

version only has one retaining ring.

3. Loosen screws (F) so that spider assembly (H) will turn clock wise. It is

not necessary to completely remove screws (F) from fixture. Once spider
assembly (H) is loose turn until it slips over the heads of the screws. Set
aside for later use (Figure 2).

4. Using two machine screws (not provided) attach cross bar (A) to the

electric box using inside oval holes to orient fixture.

Note: A new electric box comes with screws. When replacing a fixture,
retain the screws for use with the new fixture.

(Figure 1)

5. Start threaded studs (B) into appropriate holes in crossbar (A).

6. Using suitable wire connectors (not provided), connect the fixture wires to

the supply wires, (white to white, black to black, bare copper or green to
bare copper or green). If the fixture is wired with twin lead lamp cord,
connect the ribbed side to white, and the smooth side to black.

Caution: Make sure wire connectors are twisted on securely and no bare
wires are exposed.

7. Apply a generous bead of a suitable caulking material to caulking lip (E)

on the fixture (Figure 3).

8. Carefully tuck all wires behind the fixture. Place fixture (C) over threaded

studs (B) and tighten firmly to mounting surface using barrel knobs (D).

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 2)

(Figure 3)

(continued)

22419

Installation Instructions B162

For Outdoor Wall sconce 30-5610 & 30-5610F Page 2 of 2

To Install Outer Glass (Figure 4)

Component Parts

F Screws (3)
H Spider Assembly
I Socket
J Outer Glass (larger diameter glass)

1. Slip outer glass (J) into spider assembly (H).

2. Raise spider assembly (H) with outer glass (J) installed and slip over socket (I)

aligning holes in the top of the spider assembly (H) so keyed ring goes over
screws (F).

3. Turn spider assembly (H) counter clockwise until it stops. Tighten three screws

(F) until snug against the spider assembly. Be careful not to over tighten.

To Install Inner Glass

Component Parts

G Retaining Ring (“F” version only 1)
K Inner Glass

(Figures 5)

(Figure 4)

1. Slip inner glass (K) over socket.

2. Thread the first retaining ring (G) on to socket until it is against top of the

inner glass (K).

3. Thread the second retaining ring (G) onto socket until it is snug against the

first retaining ring. Do not over tighten. Disregard this step for the “F”
version.

4. Install light bulb. “F” version bulb is included.

5. Restore electricity at main breaker.

(Figure 5)

If you need further assistance, or find that you are missing any parts, please contact
the dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22419