Page 1
Installation Instructions B226
Port Outdoor Sconces 30-4301, 30-4303 & 30-4305 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall
Component Parts
A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (2)
F Rubber Washer (1)
G Green Ground Screw
H Cupped Washer
I Caulking Lip
Caution: Be sure power is off at the main breaker
box prior to installation.
1. Carefully unpack the fixture from the carton.
(Figures 1 & 2)
(Figure 1)
2. Center the wall mount bracket (B) over the
electrical box being sure to hold it plum and level. With a pencil, mark the location of all mounting holes in the
wall mount bracket on the wall behind.
IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.
Put the wall mount bracket down and drill 1/4" holes in the locations marked
on the wall. For holes using anchors, place the tapered end of the anchors (C)
into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall
mount bracket while moving the bracket into position. Using the #10 screws
(D), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Hold the fixture assembly (A) close to the wall mount bracket and using
suitable wire connectors (not provided), connect fixture wires to supply wires
(white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (G) and cupped washer (H)
(Figure 2)
to secure a pigtail lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
5. Apply a generous bead of a suitable caulking material to calking lip (I) on the fixture (not provided). (Figure 2)
6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture firmly
onto bracket (B) and fasten with #8 black screw (E) and rubber washer (F) on top.
7. Install 2
nd
black screw (E) in bottom of fixture attaching to wall mounting bracket (B).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26779
Page 2
Installation Instructions B226
Port Outdoor Sconces 30-4301, 30-4303 & 30-4305 Page 2 of 2
To Install Glass (Figure 3)
Component Parts
A Fixture Assembly
J Socket
K Glass
L Inner Glass Diffuser
M Retaining Ring
N Retaining Ring Tool
1. Remove retaining ring (M) from socket (J). Retaining ring ships installed.
2. Slip glass (K) and inner glass diffuser (L) over socket (J).
3. Thread retaining ring (M) onto socket (J) using retaining ring tool (N)
provided until it rest on inside of the inner diffuser glass (L). Do not over
tighten.
4. Install bulb. Not Included.
To Install Decorative Forged Ring
Component Parts
A Fixture Assembly
O Decorative Forged Ring
P Thumb Screw (2)
1. Remove thumb screws (P) from fixture assembly (O).
Thumb screws ship installed.
2. Slide decorative forged ring (O) onto fixture assembly (A).
3. Thread both thumb screws (P) through decorative forged
ring (O) and into the fixture assembly (A). Tighten screws
to complete installation.
4. Restore electricity at main breaker.
(Figure 4)
(Figure 3)
If you need further assistance, or find that you are missing any parts, please
contact the dealer from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 4)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
26779
Loading...