Hubbardton Forge 217730 User Manual
Installation & Assembly Instructions B108
Ono Sconce 21-7730F Page 1of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Install (Figure 1)
Component Parts
A Fixture
B Mounting Plate
C Ground Screw
D Screws (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Place the wall mounting plate (B) over the electrical box
using the center hole provided being sure to hold it plum
and level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on the wall
behind. Set aside the wall mounting plate and drill 1/4"
holes in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (F) into the
holes and gently tap them flush to the wall using a light
weight hammer. Using two machine screws (not
provided), fasten the mounting plate (B) to the outlet box,
making sure the mounting holes are level.
Note: A new outlet box comes with screws. When
replacing a fixture, retain the screws for use with the new
fixture.
IMPORTANT: Fixture must be secured to a solidly
mounted electrical box. If in doubt, contact a qualified
electrician.
3. Move fixture (A) into position. Using suitable wire connectors (not provided), connect the fixture wires to the
supply wires; white to white, black to black, and bare copper or green to bare copper or green. Connect all ground
wires to mounting plate (B) using cupped washer (E) and ground screw (C).
Caution: Make sure wire connectors are twisted on securely and no bare wires are exposed.
4. Place fixture firmly against wall and fasten with two screws (D).
5. Install light bulb provided. (13 watt T2 fluorescent)
6. Restore electricity at main breaker.
E Cupped Washer
F Anchors (4)
G #10 Screws (4)
(Figure 1)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
19750 Rev B
Installation & Assembly Instructions B108
Ono Sconce 21-7730F Page 2of 2
To Install Glass (Figures 2 & 3)
Component Parts
H Fixture Front
I Machine Screw (2)
J Glass
1. Slide glass (J) in opening on front side of fixture front (H). Adjust until sides
2. Install 2 machine screws (I) in locations provided on fixture front (H). Tighten
are equally spaced with fixture front.
Note: For glass orientation see Figure 3.
screws against glass being careful not to over tighten.
(Figure 2)
(Figure 3)
To Install Fixture Front
Component Parts
A Fixture
H Fixture Front
K Machine Screw (2)
(Figure 4)
1. Install fixture front (H) on fixture (A).
2. Install 2 machine screws (K) and tighten.
(Figure 4)
If you need further assistance, or find that you are missing any parts, please
contact the dealer from which you purchased this product. We hope you enjoy your fixture!
*
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19750 Rev B
Loading...