Installation & Assembly Instructions B116
For Silhouette Sconces 21-7705F, 21-7710F, 21-7715F & 217720F Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
For fixtures requiring assembly, please refer to assembly instructions before installation.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Install (Figure 1)
Component Parts
A Fixture
B Mounting Plate
C Ground Screw
D Screws (2)
E Socket Screw (2)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Place the wall mounting plate (B) over the electrical box
using the center hole provided being sure to hold it plum
and level. With a pencil, mark the location of all mounting
holes in the wall mount bracket on the wall behind. Set
aside the wall mounting plate and drill 1/4" holes in the
locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (G) into the holes and
gently tap them flush to the wall using a light weight
hammer. Using two machine screws (not provided), fasten
the mounting plate (B) to the outlet box, making sure the
mounting holes are level.
Note: A new outlet box comes with screws. When
replacing a fixture, retain the screws for use with the new
fixture.
IMPORTANT: Fixture must be secured to a solidly mounted
electrical box. If in doubt, contact a qualified electrician.
F Cupped
Washer
G Anchors (4)
H #10 Screws (4)
(Figure 1)
3. All fixtures are shipped with the socket screws (E) in the number two position. For product 21-7705F (River
Sconce) the screws need to be removed and the sockets moved up to the number one position. Thread socket
screw (E) in the number one location until snug.
Note: Sockets may be adjusted for the other front panels per personal preference. Socket screws (E) should
always be in the same corresponding holes. (1 & 1, 2 & 2).
4. Move fixture (A) into position. Using suitable wire connectors (not provided), connect the fixture wires to the
supply wires; white to white, black to black, and bare copper or green to bare copper or green.
Connect all ground wires to mounting plate (B) using cupped washer (F) and ground screw (C).
Caution: Make sure wire connectors are twisted on securely and no bare wires are exposed.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19865 Rev C
(continued)
Installation & Assembly Instructions B116
For Silhouette Sconces 21-7705F, 21-7710F, 21-7715F & 217720F Page 2 of 3
5. Carefully tuck all wires behind the fixture, place fixture firmly against the wall and fasten with 8-32 screws (D).
Note: Ballast disconnect should be located in center of electrical box.
6. Install light bulbs. (See bulb installation at the end of the instructions)
7. Restore electricity at the main breaker.
8. Refer to glass and front mounting instructions on the next page for complete
installation.
To Install Side Diffuser Glass
Component Parts
I Diffuser (2)
J Diffuser Clip (4)
K Corner Blocks
(Figure 2)
1. Install diffuser (I) so it rests between corner blocks (K) and diffuser clip (J).
To Install Front Glass & Plate
Component Parts
A Fixture
L Glass Panel
M Front Plate
N Screw (4)
O Foam Washer (4)
(Figure 3)
1. Remove the four screws (N) from the front of fixture (A).
2. Install four adhesive backed foam washers (O) onto front of fixture
(A) to help cushion glass panel (L).
3. Slip screw (N) through front plate (M) and glass panel (L).
4. Thread screw (N) into fixture (A) until snug against front plate (M).
(Figure 2)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 3)
(continued)
19865 Rev C
Installation & Assembly Instructions B116
For Silhouette Sconces 21-7705F, 21-7710F, 21-7715F & 217720F Page 3 of 3
To Install Bulbs (Figure 4)
Component Parts
P Socket
Q T2 Bulb (2 Each)
1. Slide bulb (Q) into Socket (p) making sure the bulbs seat
completely into socket oriented as shown. (See trouble shooting
solutions below).
If fixture does not light or blinks and then goes off try the following:
1. Make sure the bulbs are correctly installed into sockets. Push
gently on the ends of the bulbs to make completely sure the bulbs
are making contact with the sockets.
2. Check overall fit. Bulbs are designed to fit snugly into both
sockets. Too much clearance on either end could cause the bulbs
to arc and fail prematurely.
3. If fixture still will not light try removing both bulbs and
reinstalling them along with switching power off to the fixture.
(Figure 4)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
*
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19865 Rev C
Loading...