Page 1
Installation Instructions B100
Mosaic Sconce 21-7628 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
After installation extra hardware and accessories are possible; our kits are used on multiple products and options.
To Install Fixture (Figure 1)
Component Parts
A Bulb Shield E Crossbar
B Bulb (included) F Ground Screw
C Knurl Ball (2) G Threaded Stud (2)
D Fixture Back H Socket
Caution: Be sure power is off at the main breaker
box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided) attach
crossbar (E) to the electric box using inside oval
holes to orient fixture. Verify crossbar
orientation is correct before attaching
new electric box comes with screws. When
replacing a fixture, retain the screws for use with
the new fixture.
3. Thread studs (G) into the appropriate holes in
the crossbar (E). Adjust the studs (G) to proper
length to ensure the fixture will fit snugly to the
wall.
4. Using suitable wire connectors (not provided),
connect the fixture wires to the supply wires,
(white to white, black to black, bare copper or
green to bare copper or green). If the fixture is
wired with twin lead lamp cord, connect the
ribbed side to white, and the smooth side to
black. Ground the crossbar (E) using the green
ground screw (F) to secure a pigtail leads to the
crossbar.
are twisted on securely and no bare wires are
exposed.
Caution: Make sure wire connectors
5. Carefully tuck all wires behind the fixture back (D), place fixture back (D) firmly against the wall and fasten with
knurled balls (C).
6. Install light bulb (B). Be careful not to touch bulb with bare hands; oil from your hands will reduce bulb life.
7. Install the light bulb shield (A) by carefully threading it onto the socket (H).
8. Restore electricity at main breaker.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
. Note: A
(Figure 1)
(continued)
19440
Page 2
Installation Instructions B100
Mosaic Sconce 21-7628 Page 2 of 2
To Install Glass (Figures 2 & 3)
Component Parts
I Fixture Front Panel
J Nylon Screw
K Glass
L Angled Retaining Cup
M Panel Leg
N Bracket Clip
O Ball Screw
1. Insert glass (K) into fixture front panel (I). The glass sits into the
angled retaining cup (L) inside the curved portion of the panel.
Secure glass in position by tightening ball screw (J) against glass.
Do not over tighten. Please note that several colors of glass have
been included and may change as desired.
2. Attach fixture front panel (I) to back of fixture by inserting panel
legs (M) into bracket clips (N).
3. Secure by threading ball screw (O) up into hole in the socket
bracket.
(Figure 2)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
(Figure 3)
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
19440
Loading...