Page 1
Installation Instructions B178
For Aperture Vertical Sconce 21-7520 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products
and options.
To Mount Fixture to Wall (Figures 1 & 2)
Component Parts
A Fixture Back
B Fixture Front
C Locking Screw
D Cap Screw (2)
E Screw Cap
F Nipple
G Lock Nut
H Crossbar
I Ground Screw
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Remove fixture front (B) from fixture back (A) by loosening locking screw (C). Two
assemblies are shipped together. Slide fixture front (B) up to allow it to slip over
cap screws (D). Set aside for later use.
3. Using two machine screws (not provided) attach cross bar (H) to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the
screws for use with the new fixture.
4. Thread the nipple (F) into the crossbar (H) and secure with lock nut (G).
Adjust the nipple to proper length to ensure the fixture will fit snugly to
the wall.
5. Using suitable wire connectors (not provided), connect the fixture wires
to the supply wires, (white to white, black to black, bare copper or green
to bare copper or green). Ground the crossbar using the green ground
screw (I) and securing a pigtail lead to the crossbar. If the fixture is
wired with twin lead lamp cord, connect the ribbed side to white, and the
smooth side to black. Caution: Make sure wire connectors are twisted
on securely and no bare wires are exposed.
6. Carefully tuck all wires behind the fixture back (A), place fixture back
firmly against the wall and fasten with screw cap (E).
7. See instructions following to complete install.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22738
Figure 1
Figure 2
(continued)
Page 2
Installation Instructions B178
For Aperture Vertical Sconce 21-7520 Page 2 of 2
To Install Glass
Component Parts
B Front Assembly
J Glass (2)
K Glass Spring
1. Slide glass (J) into slots in front assembly (B) with the dull side towards the
center until the holes in the glass (J) engage with the glass spring (K).
To Install Front
Component Parts
A Fixture Back
B Front Assembly
C Locking Screw
(Figure 3)
(Figure 4)
D Cap Screw (2)
L Bulb (Included)
1. Install light bulb (L). Be careful not to touch bulb with bare hands; oil
from your hands will reduce bulb life.
2. Slip front assembly (B) onto two cap screws (D) by aligning top slot
and keyed slot with the cap screws (D) installed in fixture (A). When
front is as far back as it will go slide fixture down to secure.
3. Tighten locking screw (C) until snug.
If you need further assistance, or find that you are missing any parts, please
contact the dealer from which you purchased this product. We hope you enjoy
your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper
installation, lamping or use of this fixture.
(Figure 3)
(Figure 4)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22738
Loading...