Hubbardton Forge 213310 User Manual

Installation Instructions B256

Oculus Sconce/Semi-flush 21-3310 Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

After installation extra hardware and accessories are possible; our kits are used on multiple products and options.

To Prepare Fixture (Figure 1)

Component Parts

A Fixture
B Forged Cone Assembly

1. Carefully unpack the fixture from the carton.

2. Spin forged cone assembly (B) counterclockwise until it separates

from the fixture (A).

3. Set aside for later use.

To Mount Fixture to Wall

Component Parts

A Fixture
C Crossbar
D Threaded Stud (2)
E Knurled Ball (2)
F Ground Screw

Caution: Be sure power is off at the main breaker box
prior to installation.

(Figure 2)

(Figure 1)

1. Using two machine screws (not provided), fasten the

crossbar (C) to the electric box making sure that
fixture mounting holes are level.

electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new
fixture.

Note: A new

2. Thread studs (D) into the appropriate holes in the

crossbar (C). Adjust the studs to proper length to

(Figure 2)

ensure the fixture will fit snugly to the wall.

3. Hold the fixture (A) close to the wall and using suitable wire connectors, not provided, connect fixture wires to

supply (white to white or ribbed and black to black or smooth). Run a pigtail lead from crossbar ground screw (F)
to the junction box and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

4. Slide fixture (A) over threaded studs (D) and push firmly to wall, making sure that no wires are pinched between

fixture and wall. Fasten with knurled balls (E). Be sure threaded studs (D) are fully seated in the knurled balls (E).

5. See instructions following to complete installation.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

27014

Installation Instructions B256

Oculus Sconce/Semi-flush 21-3310 Page 2 of 3

To Install Glass (Figure 3)

Component Parts

A Fixture
G Glass
H Threaded Stud (4)
I Rubber Washer (8)

1. Install 2 rubber washers (I) onto

each threaded stud (H) and thread
the threaded studs (H) into the
blocks on the fixture (A). Be sure
to screw the studs (H) in far enough
so the glass will slip over.

2. Place glass (G) onto fixture (A).

Line up holes in glass (G) with
threaded studs (H).

3. Thread the threaded studs (H) out

evenly until the rubber washers (I)
fit snug against the glass. Be sure
not to over tighten.

(Figure 3)

To Install Bulb

Component Parts

J Socket
K Bulb (Included)

1.

Install light bulbs (K) into sockets (J). Be

(Figure 4)

careful not to touch bulb with bare hands;
oil from the hands will dramatically reduce
bulb life.

Note: The bulb included is based on our
design preference; see the fixtures wattage
sticker for Max wattage information.

(Figure 4)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

27014

(continued)