Hubbardton Forge 213256 User Manual

Installation Instructions B228

Tapered Angle Sconce 21-3255 & 21-3256 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Caution: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all applications. If
installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Install Back plate (Figure 1)

Component Parts

A Cross Bar
B Threaded Studs (2)
C Ground Screw

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided),

fasten the crossbar (A) to the electric box (see
illustration), making sure that fixture
mounting holes are level.

Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use with the new fixture.

3. Thread studs (B) into appropriate holes in

crossbar (A). Adjust the studs to proper length
to ensure the fixture assembly (D) will fit
snugly against the wall.

4. Using suitable wire connectors (not provided)

connect fixture wires to supply wires (white to
white and black to black). Run a pigtail lead
from crossbar ground screw (C) to the
junction box and connect all ground wires
(bare copper or green to bare copper or green).

Caution: Make sure wire connectors are
twisted on securely, and no bare wire is
exposed.

5. Slide fixture assembly (D) over the threaded

studs (B) and push firmly against the wall
making sure that no wires are pinched
between back plate and wall. Fasten with
barrel knobs (E). Be sure that threaded studs
(B) are seated in the barrel knobs (E).

6. Install bulb and decorative face plates (see instructions below).

D Fixture Assembly
E Barrel Knobs (2)

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

26784

Installation Instructions B228

Tapered Angle Sconce 21-3255 & 21-3256 Page 2 of 2

To Install Light Bulb and Shield

Component Parts

F Socket
G Bulb (included)
H Bulb Shield

(Figure 2)

1. Install bulb (G). Be careful not to touch bulb with bare hands; oil from the hands

will dramatically reduce bulb life.

2. Place bulb shield (H) over bulb (G) and thread onto socket (F). Be careful not to

over tighten.

To Attach Decorative Face Plate

Component Parts

D Fixture Assembly
I Decorative Face Plate

(Figure 3)

1. Attach decorative face plates (I) to the fixture assembly (D) by inserting

the welded rod attaching the two angled plates into the slots and down
into the notches. Be sure the rod is seated into both notches.

2. Restore electricity at main breaker.

Cleaning Instructions

The unique finish on our copper accents is achieved by heating and oxidizing
the surface of the raw copper.

(Figure 2)

When dusting, gently wipe the surface with a soft damp cloth using a spray wax
if desired. For extra protection and a deep rich finish, a light application of paste
wax once a year is desirable. Never scrub or use an abrasive.

NEVER USE AMMONIA OR SOLVENT-BASED CLEANING
PRODUCTS ON THE COPPER SURFACE.

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26784