Hubbardton Forge 209310 User Manual

Installation Instructions B93

For Forged Bar Sconce 20-9310 & 20-9311 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Install Fixture (Figures 1 & 2)

Component Parts

A Wall Mount Bracket
B Anchors
C #10 Screws
D Fixture Assembly
E #8 Black Screws
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker box prior to
installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (A) over the electrical box

being sure to hold it plum and level. Note: Specific electrical

box will need to be used to prevent it being visible after
installation (Figure 2). If the wall mount bracket has a notch orient bracket

with notch at the bottom. With a pencil, mark the location of all mounting holes
in the wall mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted
electrical box and/or a framing member in at least two locations. Do not depend
on drywall anchors alone to support this fixture. If in doubt, contact a qualified
electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on
the wall. For holes using anchors, place the tapered end of the anchors (B) into
the holes and gently tap them flush to the wall using a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket

while moving the bracket into position. Using the 1" #10 screws (C), screw the bracket
securely to the wall. Be careful not to over-tighten or strip the anchors.

4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket. Leave the bottom

screws out for now.

5. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare copper or
green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail
lead to the bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(Figure 1)

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19433 Rev B

Installation Instructions B93

For Forged Bar Sconce 20-9310 & 20-9311 Page 2 of 2

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screws in the top of the bracket go through the holes in the top of the fixture. Secure the
fixture by threading the remaining black #8 screws up through the holes in the bottom of the fixture and into the
mounting bracket.

7. Install light bulb(s) and restore electricity at main breaker.

To Install Glass

Component Parts

H Retaining Ring
I Glass
J Lamp Socket

(Figure 3)

1. Place glass (I) over lamp socket (J).

2. Thread retaining ring (H) on to lamp socket (J) until it reaches the bottom

of the glass (I).

To Attach Shade

Component Parts

I Glass
K Shade Clip (3)
L Shade Spider
M Shade

(Figure 4)

1. Attach the (3) shade clips (K) to shade spider (L) leaving clearance for the edge of

the glass (I). Shade clip should push onto first curved area of spider.

2. Place shade so that shade spider rests on top edge of glass.

3. Slide shade clips out towards edge of glass equally to center the shade. Slide clips

until the notch engages with the top edge of the glass.

(Figure 3)

(Figure 4)

If you need further assistance, or find that you are missing any parts, please contact
the dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19433 Rev B