Hubbardton Forge 209250 User Manual

Installation Instructions B124

For Swing Arm Sconce 20-9250 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Install Fixture (Figure 1)

Component Parts

A Wall Mount Bracket
B Anchors
C #10 Screws
D Fixture Assembly
E #8 Black Screws
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (A) over the electrical box being sure to hold it

plum and level. Note: Specific electrical box will need to be used to prevent it being visible after installation
(Figure 2). If the wall mount bracket has a notch orient bracket with notch at the bottom. With a pencil, mark the
location of all mounting holes in the wall mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support
this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on
the wall. For holes using anchors, place the tapered end of the anchors (B) into
the holes and gently tap them flush to the wall using a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount

bracket while moving the bracket into position. Using the 1" #10 screws (C),
screw the bracket securely to the wall. Be careful not to over-tighten or strip the
anchors.

4. Thread the black # 8 screws (E) up through the holes in the top of the wall

mount bracket. Leave the bottom screws out for now.

5. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare copper or
green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail
lead to the bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screws in the top of the bracket go through the holes in the top of the fixture. Secure the
fixture by threading the remaining black #8 screws up through the holes in the bottom of the fixture and into the
mounting bracket.

(Figure 1)

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

20851 Rev A

Installation Instructions B124

For Swing Arm Sconce 20-9250 Page 2 of 2

To Install Glass & Shade (Figure 3)

Component Parts

H Retaining Ring
I Shade
J Glass Diffuser
K Socket

1. Slip glass diffuser (J) over socket (K).

2. Slip center ring of shade (I) over socket until it rests on top

of diffuser glass (J).

3. Thread retaining ring (H) onto socket until it rests on top of

shade (I). Do not over tighten.

4. Install light bulb(s) and restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact
the dealer from which you purchased this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 3)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

20851 Rev A