Page 1
Installation & Assembly Instructions B118
g
For Exos Wave Wall Sconce 20-7875 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum watta
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Install Fixture (Figure 1)
Component Parts
A Wall Mount Bracket
B Anchors (6)
C #10 Screws (6)
D Fixture
Caution: Be sure power is off at the main
breaker box prior to installation.
1. Carefully unpack the fixture from the
carton.
2. Center the wall mount bracket (A) over the
electrical box being sure to hold it plum
and level. With a pencil, mark the location
of all mounting holes in the wall mount
bracket on the wall behind. Measure up 1
3/8” from center of the wall mount bracket
and out 16” to locate outside wall mount
bracket locations. Mark center location of
both outside wall mount bracket (H).
IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing member in at least two
locations. Do not depend on drywall
anchors alone to support this fixture. If in
doubt, contact a qualified electrician.
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the 1" #10 screws (C), screw the brackets securely to the wall. Be careful not to over-tighten
or strip the anchors.
4. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare copper or
green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail
lead to the bracket.
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
(continued)
e noted on fixture. Use only recommended bulbs with fixture.
E #8 Black Screws (6)
F Green Ground Screw
G Cupped Washer
H Outside Wall Mount Bracket
(Figure 1)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19873 Rev B
Page 2
Installation & Assembly Instructions B118
For Exos Wave Wall Sconce 20-7875 Page 2 of 2
5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over
the brackets so that the screw (E) in the top of the brackets go through the hole in the top of the fixture. Secure the
fixture by threading the remaining black #8 screw (E) up through the hole in the bottom of the fixture and into the
mounting brackets.
6. Install light bulb (Figure 2, I). Be careful not to touch bulb with bare hands. Oil from the hands will dramatically
reduce bulb life.
7. Thread bulb shield (Figure 2, J) onto socket. Future bulb changes may be accomplished by snapping glass bulb
shield on and off rather than unthreading the holder
8. Restore electricity at main breaker.
To Install Glass
Component Parts
D Fixture
G Glass (10)
H Metal Glass Clip (10)
I Bulb
J Bulb Shield
(Figure 2)
1. Mount metal glass clip (H) into notches on
fixture (D).
2. Slide glass (G) into back slots in fixture from
the side (start from left or right side not the
center).
3. Slide front glass (G) into fixture from the
top.
4. Align the glass until it protrudes equal
amounts on both sides of fixture.
(Figure 2)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
*
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19873 Rev B
Loading...