Hubbardton Forge 207871 User Manual

Installation Instructions B106

g

Exos Wave Sconce Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Install Fixture (Figure 1)

Component Parts

A Wall Mount Bracket
B Anchors (4)
C #10 Screws (4)
D Fixture

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (A) over the

electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on
the wall behind.

IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing member in at least two
locations. Do not depend on drywall anchors
alone to support this fixture. If in doubt,
contact a qualified electrician.

Put the wall mount bracket down and drill
1/4" holes in the locations marked on the
wall. For holes using anchors, place the
tapered end of the anchors (B) into the holes
and gently tap them flush to the wall using a
light weight hammer.

3. Thread the wires in the electrical box

through the center hole in the wall mount bracket while
moving the bracket into position. Using the 1" #10
screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or strip the anchors.

4. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare copper or
green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail
lead to the bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

e noted on fixture. Use only recommended bulbs with fixture.

E #8 Black Screws (2)
F Green Ground Screw
G Cupped Washer

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19499 Rev B

Glass Installation Instructions B106

Exos Wave Sconce Page 2 of 2

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screw in the top of the bracket go through the hole in the top of the fixture. Secure the
fixture by threading the remaining black #8 screw up through the hole in the bottom of the fixture and into the
mounting bracket.

6. Install light bulb (Figure 2, D). Be careful not to touch bulb with bare hands. Oil from the hands will dramatically

reduce bulb life.

7. Thread bulb shield (Figure 2, E) onto Socket. Future bulb changes may be accomplished by snapping glass bulb

shield on and off rather than unthreading the holder

8. Restore electricity at main breaker.

To Install Glass

Component Parts

A Glass (2)
B Fixture
C Metal Glass Clip (2)
D Bulb
E Bulb Shield

(Figure 2)

1. Slide glass (A) into back slots in fixture from

the side.

2. Attach metal glass clip (C) into notches on

fixture (B).

3. Slide front glass (A) piece into fixture from t

top.

4. Align the glass until it protrudes equal

amounts on both sides of fixture.

he

(Figure 2)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

*

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19499 Rev B