Hubbardton Forge 207805 User Manual
Assembly & Installation Instructions B265
Figure 1
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Ondrian Wall Sconce 20-7801 & 20-7805 Page 1 of 2
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mounting Bracket D Electric Box Cover (for 4” Outlet box)
B Anchors (2) E # 8 Black Screw (3)
C #10 Screws (2) F Fixture Assembly
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Place the wall mounting bracket (A) over the electrical box using one
of the wiring holes provided being sure to hold it plum and level. If
using a single gang outlet box electric box, cover (D) is not needed.
Remove #8 black screw (E) from electric box cover (D) and save for
later use. Determine which electric box cover (D) location works the
best and attach to wall mounting bracket (A). With a pencil, mark the
location of all mounting holes in the wall mount bracket on the wall
behind.
IMPORTANT: Wall mounting bracket must be secured to a solidly
mounted to a framing member in at least two locations. Do not depend
on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.
Drill 1/4" holes in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (B) into the holes and gently
tap them flush to the wall using a light weight hammer.
3. Thread the wires in the electrical box through the hole in the wall mounting bracket (A) while moving the bracket
into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Hold the fixture assembly (F) close to the wall mounting bracket (A) and using suitable wire connectors (not
provided) connect fixture wires to supply wires (white to white, black to black, and bare copper or green to bare
copper or green). Ground the mounting bracket using the green ground wire fastened to the back of the fixture
assembly (F).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
5. Carefully tuck all wires behind the fixture assembly (F) and inside the wall mounting bracket (A) an d pla ce th e
fixture over the bracket so the holes in the top and bottom match the threaded holes in the wall mounting bracket
(A). Secure the fixture by threading the #8 black screws (E) through the holes in the fixture assembly (F) and into
the wall mounting bracket (B ).
6. Install G-9 light bulbs (included)
Note: The bulb included is based on our design preference; see the fixtures wattage sticker for Max wattage
information.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27214 B
Assembly & Installation Instructions B265
Figure 3
Figure 2
Ondrian Wall Sconce 20-7801 & 20-7805 Page 2 of 2
To Install Glass (Figure 2)
Component Parts
F Fixture
G Glass (2)
H Rubber O-Ring (2)
I Knurled Ball (2)
1. Align glass (G) so that the bulb passes through the large hole and
threaded rod passes through smaller hole
2. Slide glass (G) over light b ulb s un t il it come in contact with the
fixture (F).
3. Slide rubber o-ring over threaded rod until tight against glass
4. Hold the glass in place while threading the knurled ball (I) onto the
threaded rod until tight.
To Install Center Badge (Figure 3)
Component Parts
J #8 Black Hex Head Screw
K Center Badge Assembl y
1. Remove screw (J) from glass mounting bracket. Save for later
use. Screw is shipped installed in bracket.
2. Slide center badge assembly (K) onto the mounting bracket until
it touches
Align small threaded hole in the mounting bracket with hole in
center badge assembly (K).
3. Attach center badge assembly (K) to mounting bracket with
screw (J). Tighten with provided Allen wrench.
Note: The center badge can be mounted as shown or in reverse.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27214 B
Loading...