Hubbardton Forge 207765 User Manual

Installation Instructions B293

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL

(Figure 1)

Ethos Sconce 20-7760D & 20-7765D Page 1 of 2

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or
electrician

To Mount Fixture to Wall (Figure 1)

Component Parts

Caution: Be sure power is off at the main breaker box prior to installation.

.

A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (2)
F Rubber Washer (2)
G Green Ground Screw
H Cupped Washer

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on
the wall behind.

IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing member in at least two
locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a qualified
electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using
a light weight hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the

bracket into position. Using two machine screws (not provided), fasten the wall mount bracket (B) to the
electric box making sure that the bracket is level. Using the #10 screws (D), screw the bracket securely to
the wall. Be careful not to over-tighten or strip the anchors.

Note: A new electrical box comes with screws. When replacing a fixture, retain the existing screws for use
with the new fixture.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connecto rs (no t

provided), connect fixture wires to supply wires (white to white or ribbed and black to black or smooth).
Ground the mounting bracket using the green ground screw (G) and cupped washer (H) to secu re a pigtail
lead to the bracket and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28305

Installation Instructions B293

(Figure 3)

Ethos Sconce 20-7760D & 20-7765D Page 2 of 2

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture

firmly onto bracket (B) and fasten with #8 black screw (E) and rubber washer (F) on top.

6. Install 2

To Install Glass (Figure 3)

Component Parts

A Fixture Assembly
J Decorative Glass
K Glass Diffuser
L Top Bracket
M Set Screw (3)
N Plastic Bumper

1. Set Screws (M) are shipped installed in the fixture. Prior to glass installation,

ensure that all set screws (M) are unscrewed enough to allow installation of
glass.

2. Slide glass diffuser (K) down into the fixture from the top. Diffuser should be

seated in the bottom bracket.

3. Tighten set screw (M) in bottom bracket against glass diffuser (K). Do not

over tighten.

4. If desired, the plastic bumper (N) can be adhered to the top of the decorative

glass (J).

5. Slide decorative glass (J) down into the fixture from the top. Decorative glass

should be seated in the bottom bracket.

6. Slide top bracket (L) into the fixture. Check fit between set screw (M) in top

bracket (L) and glass diffuser (K). Adjust Set Screw as necessary to contact
glass diffuser (K). Note: Removal of Top Bracket is necessary to adjust Set
Screw. Once top bracket is seated in fix ture, ag ains t the glass, t ighten the set
screw (M) in fixture (A) against top bracket (L).

7. Restore electricity at main breaker.

nd

black screw (E) in bottom of fixture attaching to wall mounting bracket (B).

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you
purchased this product. We hope you enjoy your fixture!

*

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

28305