Hubbardton Forge 207720 User Manual

Installation Instructions B221

For Wall Sconce 20-7710 & 20-7720 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (4)
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker
box prior to installation.

1. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on
the wall behind.

IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing member in at least two locations. Do not
depend on drywall anchors alone to support this fixture. If in
doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.

2. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten
or strip the anchors.

3. Thread the black # 8 screws (E) up through the hole in the top of the wall mount bracket (B). Leave the bottom

screw out for now.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer
(G) to secure a pigtail lead to the bracket.

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screw in the top of the wall bracket go through the hole in the top of the fixture. Secure the
fixture by threading the remaining black #8 screws (E) up through the hole in the bottom of the fixture and into
the mounting bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 1)

(continued)

26493

Installation Instructions B221

For Wall Sconce 20-7710 & 20-7720 Page 2 of 2

To Install Glass (Figures 4)

Component Parts

H Bulb (Included)
I Glass
J Thumb Screw

1. Install bulb (H). Be careful not to touch bulb with bare hands; oil

from the hands will dramatically reduce bulb life.

2. Loosen the three thumb screws (J). It is not necessary to remove

them from the fixture.

3. Raise glass (I) until groove is aligned with thumb screws (J).

4. Tighten the three thumb screws (J) equal amounts until snug with

glass (I). Be careful not to over tighten.

5. Restore electricity at main breaker.

(Figure 2)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

26493