Hubbardton Forge 207525 User Manual

Installation Instructions B128

For Ellipse Sconces 207525, 207525F, 207535 & 207535F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1 & 2)

Component Parts

A Wall Mount Bracket
B Anchors (4)
C #10 Screws (4)
D Fixture Assembly
E #8 Black Screws (4)
F Green Ground Screw
G Cupped Washer
H Wireway Cover
I Barrel Knob (2)

Caution: Be sure power is off at the main
breaker box prior to installation.

1. Carefully unpack the fixture from the

carton.

2. Center the wall mount bracket (A) over

the electrical box being sure to hold it
plum and level. With a pencil, mark the
location of all mounting holes in the w
mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to
a solidly mounted electrical box and/or a framing
member in at least two locations. Do not depend on
drywall anchors alone to support this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight
hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.

4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket (A). Leave the bottom

screws out for now.

5. Remove the wireway cover (H) and save for later installation.

6. Hold the fixture assembly (D) close to the wall mount bracket (A) ground the mounting bracket using the green

ground screw (F) and cupped washer (G) to secure a pigtail lead to the bracket.

all

(Figure 1)

This illustration represents a typical fixture

and may not match every style.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21028

Installation Instructions B128

For Ellipse Sconces 207525, 207525F, 207535 & 207535F Page 2 of 2

7. Place the fixture over the bracket so that the screws in the top of the wall bracket go through the holes in the top

of the fixture. Pull the four supply wires and ground wires through the front wireway area. Secure the fixture by
threading the remaining black #8 screws up through the holes in the bottom of the fixture and into the mounting
bracket. (See Figure 2)

8. Using suitable wire connectors (not provided), connect fixture wires to supply wires (white to white, black to

black, and bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

9. Carefully tuck all wires behind the

fixture assembly and inside the wall
mount bracket.

10. Install the wireway cover (H) and secure

with barrel knobs (I).

To Install Glass (Figure 3)

Component Parts

J Socket (3)
K Glass (3)
L Retaining Ring (3)
M Socket Tool

1. Slip glass (K) over socket (J).

2. Thread retaining ring (L) onto socket using socket

tool provided (M) until it rests on inside of glass
(K). If socket tool does not fit retaining ring tool
can be adjusted by squeezing to decrease inside
diameter to better fit the retaining ring. Do not over
tighten.

3. Install light bulbs and restore electricity at main

breaker.

(Figure 2)

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21028