Hubbardton Forge 206745 User Manual

Installation Instructions B47

For Forged Wave Sconce 20-6745L & 20-6745R Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Crossbar
B Threaded Stud (2)
C Knurl Ball (2)
D Fixture Assembly
E Ground Screw

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten

the crossbar (A) to the electric box making sure
that fixture mounting holes are level.

Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use
with the new fixture.

3. Thread studs (B) into the appropriate holes in the

crossbar (A). Adjust the studs to proper length to
ensure the fixture will fit snugly to the wall.

4. Hold the fixture assembly (D) close to the wall

and using suitable wire connectors, not provided,
connect fixture wires to supply (white to white

or ribbed and black to black or smooth). Connect
all ground wires to ground screw.

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

5. Slide fixture assembly (D) over threaded studs (B) and push firmly to wall, making sure that no wires are pinched

between fixture back and wall. Fasten with knurl balls (C). Be sure threaded studs (B) are fully seated in the
knurl balls (C).

6. See instructions on next page to install glass.

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

16163 Rev A

Installation Instructions B47

For Forged Wave Sconce 20-6745L & 20-6745R Page 2 of 2

To Install Bulbs and Glass

Component Parts

F Hanger Rod
G Glass
H Rubber tubing (2)
I Hanger Bracket
J Retaining Screw
K Bulb (2)
L Bulb Shield (2)
M Socket (2)

(Figure 2)

1. Install light bulb (K) (included). Be careful not to

touch bulb with bare hands. Oil from the hands will
dramatically reduce bulb life.

2. Thread bulb shield (L) onto socket (M). Future bulb

changes may be accomplished by snapping glass
bulb shield on and off rather than unthreading the
holder

3. Slide hanger rod (F) into holes in glass (G) from the

inside.

4. Move rubber tubing (H) outward on rod to secure

rod in glass, making sure the rod remains centered in
the glass.

5. Place hanger rod (F) into hanger bracket (I) and

secure by tightening retaining screw (J).

6. Restore electricity at main breaker.

(Figure 2)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

*

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

16163 Rev A