Page 1
Installation Instructions B160
For Three Light Sconce 20-6603 & 20-6603F Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Please Note: After installation, extra hardware and accessories may be left due to kits being used on multiple products.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mount Bracket
B Anchors (8)
C #10 Screws (8)
D Fixture Assembly
E #8 Black Screws (4)
F Green Ground Screw
G Cupped Washer
H Hanger (2)
Caution: Be sure power is off at the main breaker
box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (A) over the
electrical box being sure to hold it plum and
level. If the wall mount bracket has a notch
orient bracket with notch at the bottom. With a pencil, mark the location of all mounting holes in the wall mount
bracket on the wall behind.
box and/or a framing member in at least two locations. Do not depend on drywall anchors alone to support this
fixture. If in doubt, contact a qualified electrician.
IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical
Put the wall mount bracket down and drill 1/4" holes in the
locations marked on the wall. For holes using anchors, place the tapered end of the anchors (B) into the holes and
gently tap them flush to the wall using a light weight hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket (A). Leave the bottom
screws out for now.
5. Hold the fixture assembly (D) close to the wall mount bracket and hang attached steel cable on both hangers (H)
to help support fixture during wiring. Using suitable wire connectors (not provided), connect fixture wires to
supply wires (white to white or ribbed and black to black or smooth, and bare copper or green to bare copper or
green). Ground the mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail
lead to the bracket.
6. Carefully tuck all wires and steel cable behind the fixture assembly and inside the wall mount bracket and place
the fixture over the bracket so that the screws in the top of the wall bracket go through the holes in the top of the
fixture. Secure the fixture by threading the remaining black #8 screws (E) up through the holes in the bottom of
the fixture and into the mounting bracket.
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
(Figure 1)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22270
Page 2
Installation Instructions B160
For Three Light Sconce 20-6603 & 20-6603F Page 2 of 3
To Install Glass with G9 Option (Figure 2)
Component Parts
I Glass (3)
J Socket (3)
K Bulb (Included) (3)
L Bulb Shield (3)
M Spacer
1. Install light bulb (K). Be careful not to touch bulb with bare hands; oil
from the hands will dramatically reduce bulb life.
2. Slip glass (I) over socket (J).
3. Place spacer (M) on bulb shield (L) (note orientation of spacer).
4. Thread bulb shield (L) onto socket (J) (be careful not to over tighten).
Future bulb changes may be accomplished by snapping glass portion of
barrier on and off rather than unthreading the holder.
5. Restore electricity at main breaker.
To Install Double Glass with G9 Option
Component Parts
I Glass (3)
J Socket (3)
K Bulb (Included) (3)
L Bulb Shield (3)
M Spacer (3)
N Inner Glass (3)
O Retaining Ring (3)
P Retaining Ring Tool
(Figure 3)
1. Install light bulb (K). Be careful not to touch bulb
with bare hands; oil from the hands will
dramatically reduce bulb life.
2. Slip glass (I), inner glass (N) and spacer (M) (note
orientation of spacer) over socket (J).
3. Thread retaining ring (O) onto socket (J) using
provided retaining ring tool (P).
4. Thread bulb shield (L) onto socket (J) (be careful
not to over tighten). Future bulb changes may be
accomplished by snapping glass portion of barrier
on and off rather than unthreading the holder.
5. Restore electricity at main breaker.
(Figure 2)
(Figure 3)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22270
Page 3
Installation Instructions B160
For Three Light Sconce 20-6603 & 20-6603F Page 3 of 3
To Install Glass with GU24 Option (Figure 4)
Component Parts
I Glass (3)
J Socket (3)
K Bulb (Included) (3)
Q Retaining Ring (3)
1. Remove retaining ring (Q) from socket (J). Retaining Rings are
shipped installed.
2. Slip glass (I) over socket (J).
3. Thread retaining ring (Q) onto socket. Do not over tighten.
4. Install light bulb (K) and restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
(Figure 4)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22270
Loading...