Hubbardton Forge 206601 User Manual

Installation Instructions B159

For Wall Sconce 20-6601 & 20-6601F Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly
B Wall Mount Bracket
C Anchors
D #10 Screws
E #8 Black Screws
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Center the wall mount bracket (B) over the electrical

box being sure to hold it plum and level. With a
pencil, mark the location of all mounting holes in the
wall mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.

2. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten
or strip the anchors.

3. Thread the black # 8 screw (E) up through the hole in the top of the wall mount bracket (B). Leave the bottom

screw out for now.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer
(G) to secure a pigtail lead to the bracket.

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screw in the top of the wall bracket go through the hole in the top of the fixture. Secure the
fixture by threading the remaining black #8 screw up through the hole in the bottom of the fixture and into the
mounting bracket.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

22269 Rev A

Installation Instructions B159

For Wall Sconce 20-6601 & 20-6601F Page 2 of 3

To Install Glass with G9 Option (Figure 2)

Component Parts

H Glass
I Socket
J Bulb (Included)
K Bulb Shield
L Spacer

1. Install light bulb (J). Be careful not to touch bulb with bare hands; oil from the

hands will dramatically reduce bulb life.

2. Slip glass (H) over socket (I).

3. Slip spacer (L) over socket (I) so it rests on glass (H) (note orientation of spacer).

4. Thread bulb shield (K) onto socket (I) (be careful not to over tighten). Future bulb

changes may be accomplished by snapping glass portion of barrier on and off
rather than unthreading the holder.

5. Restore electricity at main breaker.

(Figure 2)

To Install Double Glass with G9 Option

Component Parts

H Glass
I Socket
J Bulb (Included)
K Bulb Shield
L Spacer
M Inner Glass
N Retaining Ring
O Retaining Ring Tool

(Figure 3)

1. Install light bulb (O). Be careful not to touch bulb with bare hands; oil from

the hands will dramatically reduce bulb life.

2. Slip glass (H), inner glass (M) & spacer (L) (note orientation of spacer) over

socket (N).

3. Thread retaining ring (N) onto socket (I) using provided retaining ring

tool (O).

4. Thread bulb shield (K) onto socket (I) (be careful not to over tighten). Future

bulb changes may be accomplished by snapping glass portion of barrier on
and off rather than unthreading the holder.

5. Restore electricity at main breaker.

(Figure 3)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

22269 Rev A