Hubbardton Forge 206515 User Manual
Installation Instructions B294
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
Moreau Sconce 206515 Page 1 of 2
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Anchors (4)
B Wall Mount Bracket
C Cupped Washer
D Green Ground Screw
E #10 Screws (4)
F Fixture Assembly
G #8 Black Screws (4)
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (B) over the
electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on
the wall behind.
IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing mem ber in at least two locations.
Do not depend on drywall anchors alone to support
this fixture. If in doubt, contact a qualified electrician.
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (A) into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the #10 screws (E), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Hold the fixture assembly (F) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (D) and cupped washer (C) to secure a pigtail lead to the bra c k e t
and connect all ground wires (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture firmly
onto bracket (B) and fasten with #8 black screws (G) on top.
6. Install two remaining black screws (G) in bottom of fixture attaching to wall mounting bracket (B).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28320
Installation Instructions B294
(Figure 2)
Moreau Sconce 206515 Page 2 of 2
To Install Glass (Figure 2)
Component Parts
H Bulb (included)
I Retaining Ring
J Glass
K Socket
1. Remove retaining ring (I) from socket (K). Retaining Rings are
shipped installed.
2. Install bulb (H). Be careful not to touch bulb with bare hands; oil
from the hands will dramatica lly reduce bu lb life.
3. Slip glass (J) over socket (K).
4. Thread retaining ring (I) onto socket (K) until it rests on inside of
glass (J). Do not over tighten.
5. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
*
Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
28320
Loading...