Page 1
Installation Instructions B280
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 2)
(Figure 1)
For Axis Vintage Platinum Sconce 20-6430 Page 1 of 3
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Fixture should be mounted four feet above grade.
After installation extra hardware and accessories are possible; our kits are used on multiple products and options.
To Install Fixture (Figures 1 & 2)
Component Parts
A Fixture Front
B Screw
C Fixture
D Crossbar
E #8 Screw (2)
F Gr ound Screw
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Loosen the screw (B) in the bottom of the fixture (C) until the fixture front (A)
will come loose from the fixture back. Move the fixture front (A) towards the top
of the fixture (C) to remove (Figure 1).
3. Using two machine screws (not provided) attach crossbar (D) to the electric box
using inside oval holes to orient fixture.
Note: A new electric box comes with screws. When replacing a fixture,
retain the screws for use with the new fixture.
4. Using suitable wire connectors (not provided); connect the fixture wires to
the supply wires, (white to white, black to black). Run a pigtail lead from
crossbar ground screw (F) to the junction box and connect all ground wires
(bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely and no bare
wires are exposed.
5. Carefully tuck all wires behind the fixture, place fixture firmly against the
wall and fasten with two #8 screws (E). To ensure a water tight seal, apply a
thin bead of caulking around entire perimeter of the fixture.
6. Continue with installation instructions following to assemble fixture front
and glass.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
28080
(continued)
Page 2
Installation Instructions B280
(Figure 4)
(Figure 6)
(Figure 3)
(Figure 5)
For Axis Vintage Platinum Sconce 20-6430 Page 2 of 3
To Assemble Fixture Front and Glass (Figures 3 thru 6)
Component Parts
A Fixture Front
G Glass
H Hex Nut
I Threaded Stud
J Glass Bracket
K Spring
1. Place glass (H) on flat clean surface oriented as shown in Figure 3.
2. Place fixture front (A) over glass (H) (Figure 4).
3. Holding fixture front (A) and glass (H) securely
rotate them both over so fixture front (A) rests on
flat surface.
4. Remove hex nut (I) from threaded stud (J).
5. Install spring (X) at the top of the glass (T). Push
spring inside of fixture until it rests against the top
ledge of glass (T).
6. Slip glass bracket (K) on to threaded stud (J). See
Figure 6 for orientation.
7. Thread hex nut (I) onto threaded stud (J). Be careful
not to over tighten.
8. Continue with installation instructions following
to install glass.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
28080
Page 3
Installation Instructions B280
(Figure 7)
(Figure 8)
For Axis Vintage Platinum Sconce 20-6430 Page 3 of 3
To Install Fixture Front (Figures 7 & 8)
Component Parts
A Fixture Front
B Screw
L Socket
M Socket Housing
1. Install light bulb into socket (M) (bulb not included).
2. Slip fixture front (A) onto socket housing (N).
3. Tighten screw (B) to lock fixture front (A) in p la ce (Figure 8). Be careful not to
over tighten.
4. Restore electricity at the main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
28080
Loading...