Hubbardton Forge 206425 User Manual

Installation Instructions B279

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL

(Figure 1)

(Figure 2)

Axis Vintage Platinum Sconce 20-6420 & 20-6425 Page 1 of 3

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Fixture should be mounted four feet above grade.

After installation extra hardware and accessories are possible; our kits are used on multiple products and options.

To Install Fixture (Figures 1 & 2)

Component Parts

A Fixture Front
B Screw
C Fixture
D Crossbar
E #8 Screw (2)
F Gr ound Scr e w

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Loosen the screw (B) in the bottom of the fixture (C) until the fixture front (A) will

come loose from the fixture back. Move the fixture front (A) towards the top of the
fixture (C) to remove (Figure 1).

3. Using two machine screws (not provided) attach crossbar (D) to the

electric box using inside oval holes to orient fixture.

electric box comes with screws. When replacing a fixture, retain the
screws for use with the new fixture.

4. Using suitable wire connectors (not provided), connect the fixture wires

to the supply wires, (white to white, black to black). Run a pigtail lead
from crossbar ground screw (F) to the junction box and connect all
ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely and no
bare wires are exposed.

5. Carefully tuck all wires behind the fixture, place fixture firmly against

the wall and fasten with two #8 screws (E). To ensure a water tight seal,
apply a thin bead of caulking around entire perimeter of the fixture.

6. Continue with in s tal lation instructions following to assemble fixture

front and glass.

Note: A new

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28078

Installation Instructions B279

(Figure 3)

(Figure 5)

(Figure 7)

(Figure 4)

(Figure 6)

(Figure 5A)

Axis Vintage Platinum Sconce 20-6420 & 20-6425 Page 2 of 3

To Assemble Fixture Front and Glass (Figures 3 thru 6)

Component Parts

A Fixture Front
G Glass
H Hex Nut
I Threaded Stud
J Glass Bracket
K Spring (Used only on 206425)

1. Place glass (G) on flat clean surface oriented as shown in Figure 4.

2. Place fixture front (A) over glass (G).

(Figure 4).

3. Holding fixture front (A) an d glas s (G ) securely rotate

them both
over so fixture front (A) rests on flat surface.

4. Remove hex nut (H) from threaded stud (I).

5. Slide glass (G) up towards the top of the fixture.

6. Install spring (K) at the top of the glass (G). Push spring

inside of fixture until it rests against the top ledge of glass
(G). See Figure 5A.

Note: This is used on product 206425 only.

7. Slip glass bracket (J) on to threaded stud (I). See

Figure 6 for orientation.

8. Thread hex nut (H) onto threaded stud (I) and

tighten until snug. Be careful not to over tighten.

9. Continue with installation instructions following

to install fixture front.

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28078