Hubbardton Forge 206403 User Manual
Installation Instructions B205
For Axis Sconce 20-6401 & 20-6403 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
After installation extra hardware and accessories are possible due to our kits are used on multiple products and options.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mount Bracket
B Anchors
C #10 Screws
D Fixture Assembly
E #8 Black Screws
F Green Ground Screw
G Cupped Washer
Caution: Be sure power is off at the main breaker
box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (A) over the
electrical box being sure to hold it plum and
level. If the wall mount bracket has a notch
orient bracket with notch at the bottom.
With a pencil, mark the location of all mounting holes in the wall mount bracket on the wall behind.
IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight
hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket (A) while moving the
bracket into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to overÂtighten or strip the anchors.
4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket (A). Leave the bottom
screws out for now.
5. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer
(G) to secure a pigtail lead to the bracket.
6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over
the bracket so that the screws in the top of the wall bracket go through the holes in the top of the fixture. Secure
the fixture by threading the remaining black #8 screws up through the holes in the bottom of the fixture and into
the mounting bracket.
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
(Figure 1)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24450
Installation Instructions B205
For Axis Sconce 20-6401 & 20-6403 Page 2 of 2
To Install Bulb and Front Panel (Figures 2 & 3)
Component Parts
D Fixture Assembly
H Socket
I Bulb (Included)
J Bulb Shield
K Front Plate (12-6401 is glass, 12-6403 is a forged plate)
1. Install light bulbs (I). Be careful not to touch bulb with bare hands; oil from the hands will dramatically reduce
bulb life.
2. Thread bulb shield (J) onto socket (H) (bulb shield will only thread on 3 to 4 threads). Future bulb changes may be
accomplished by snapping glass portion of barrier on and off rather than unthreading the holder.
3. Slip plate or glass (K) into tabs of fixture assembly (D) aligned so equal amounts protrude on both sides.
To Install Optional Diffuser (Sold Separately) (Figure 4)
(Figure 2)
(Figure 3)
Component Parts
E #8 Black Screws
L Diffuser
M Hex Nut (2)
1. Install diffuser (L) onto screws (E) protruding through top of fixture. Note:
Due to the diffuser being aluminum and the amount of holes punched it
might have a slight arc. Mount it so the outer edges are curled down.
2. Install two hex nuts (M) on screws (E) and tighten until snug.
(Figure 4)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24450
Loading...