Hubbardton Forge 206301 User Manual

Installation Instructions B161

For Sconces 20-6301L, 20-6301R, 20-6301EL & 20-6301ER Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Crossbar
B Fixture Assembly
C Screws (2)
D Ground Screw

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the

crossbar (A) to the electric box making sure that
fixture mounting holes are level.

Note: A new electric box comes with screws. When
replacing a fixture, retain the existing screws for use
with the new fixture.

3. Hold the fixture assembly (B) close to the wall and

using suitable wire connectors, not provided, connect
fixture wires to supply (white to white or ribbed and
black to black or smooth). Run a pigtail lead from
crossbar ground screw (D) to the junction box and
connect all ground wires (bare copper or green to bare
copper or green).

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

4. Carefully tuck all wires behind the crossbar (A) and

place the fixture assembly (B) over the crossbar so the
holes in the top and bottom match the threaded holes in the
crossbar. Secure the fixture by threading the screws (C)
through the holes in the fixture assembly (B) and into the
crossbar (A) using supplied allen wrench.

5. See instructions on next page to install glass.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 1)

This illustration represents a typical fixture

and may not match every style.

(continued)

20883 Rev A

Installation Instructions B161

For Sconces 20-6301L, 20-6301R, 20-6301EL & 20-6301ER Page 2 of 2

To Install Glass with G9 Option

Component Parts

F Socket
G Bulb (Included)
H Glass
I Washer Assembly
J Retaining Ring
K Socket Tool

1. Install light bulb (G). Be careful not to touch bulb with bare hands; oil from the

hands will dramatically reduce bulb life.

2. Slip glass (H) over socket (F).

3. Slip washer assembly (I) over socket (F) so it rests on glass (H).

4. Thread retaining ring (J) onto socket (F) using provided socket tool (K). (be

careful not to over tighten).

5. Restore electricity at main breaker.

(Figure 2)

(Figure 2)

To Install Glass with GU24 Option

Component Parts

F Socket
G Bulb (Included)
H Glass
J Retaining Ring
K Socket Tool

(Figures 3 & 4)

1. Remove retaining ring (J) from socket (F). Retaining Rings are shipped

installed.

2. Slip glass (H) over socket (F).

3. Thread retaining ring (J) onto socket (F) using

provided socket tool (K) provided until it rests on
inside of glass (H). Do not over tighten.

4. Install light bulb (G).

5. Restore electricity at main breaker.

(Figure 3)

(Figure 4)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

20883 Rev A