Page 1
Assembly & Installation Instructions B284
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
(Figure 2)
(Figure 1)
Bento Sconce 20-5955F Page 1 of 3
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Prepare to Install (Figure 1)
Component Parts
A Fixture
B Wall Mounting Bracket
C 8-32 x 1 ¼” Screws (3)
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Remove three screws (C) from front of fixture (A) to release wall mounting
bracket (B).
3. Place fixture (A) and screws (C) somewhere safe for later use.
Install Wall Mounting Bracket (Figure 2)
Component Parts
B Wall Mounting Bracket
D Anchors (8)
E #10 Screws (8)
1. Place the wall mounting bracket (B) over the electrical box using one of the holes
provided, being sure to hold it plum and level. With a pencil, mark the location of
all mounting holes in the wall mount bracket on the wall behind.
IMPORTANT: Wall mounting bracket must be secured to a solid framing member
in at least four locations. Do not depend on drywall anchors alone to support this
fixture. If in doubt, contact a qualified electrician.
Set aside the wall mounting bracket and drill 1/4" holes in the center locations
marked on the wall. For holes using anchors, place the tapered end of the anchors
(D) into the holes and gently tap them flush to the wall using a lightweight
hammer.
2. Thread the wires in the electrical box through the hole in the wall mounting
bracket (B) while moving the bracket into position. Using the 1" #10 screws (E),
screw the bracket securely to the wall. Be careful not to over-tighten or strip the
anchors.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 28097 Rev B
(continued)
Page 2
Assembly & Installation Instructions B284
(Figure 3)
(Figure 4)
Bento Sconce 20-5955F Page 2 of 3
Install Fixture (Figure 3)
Component Parts
A Fixture
B Wall Mounting Bracket
C 8-32 x 1-1/4" Screws (3)
F Ground Screw
G Cupped Washer
H Threaded Standoff (3)
1. Hold the fixture (A) close to the wall mounting bracket (B) and using suitable
wire connectors (not provided) connect fixture wires to supply wires (white to
white & black to black.). Ground the mounting bracket using the green ground
screw (F) and cupped washer (G) to secure a pigtail lead to the bracket.
Connect all ground screws (bare copper or green to bare copper or green).
Caution: Make sure wire connectors are twisted on securely, and no bare
wires are exposed.
2. Carefully tuck all wires behind the fixture (A) and inside the wall mounting
bracket (B) and place the fixture over the bracket so the holes in the top and
bottom match the threaded standoffs (H) protruding from the wall mounting
bracket (B). Secure the fixture by threading the 8-32 x 1-1/4" screws (C)
through the holes in the fixture (A) and into the wall mounting bracket (B).
Note: Wall mounting bracket (B) is oriented in relation to the fixture (A) as
shown in Figure 3 such that the bracket end with the large hole matches the
fixture end with red wires.
3. See instructions on next page to install shade.
To Assemble Shade (Figure 4)
Component Parts
K Shade
L Plastic Rivet
1. Carefully unpack the shade (K).
2. Fold flaps (Figure 4) such that the three
holes are aligned.
3. Insert plastic rivet (L) through the three
holes and cap.
4. Repeat steps 2 & 3 for other side
of shade (K).
5. Trim excess length of plastic rivet (L).
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 28097 Rev B
Page 3
Assembly & Installation Instructions B284
(Figure 5)
(Figure 6)
Bento Sconce 20-5955F Page 3 of 3
Install Shade (Figures 5 & 6)
Component Parts
A Fixture
I Shade Bracket (2)
J 8-32 x 3/8” Black Screws (2)
K Shade
1. Remove both shade brackets (I) from fixture (A) by removing the black screws (J). Hold onto brackets (I) and
screws (J) for later use (Figure 5).
2. Install bulb (not included).
3. Place the shade (K) into the bracket slot of the fixture (A). Attach the shade brackets (I) with the black screws (J)
to complete the shade installation (Figure 6).
Note: Shade edges may need to be creased slightly by hand for a proper fit.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735 28097 Rev B
Loading...