Hubbardton Forge 205950 User Manual
Installation Instructions B270
CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL
(Figure 1)
Bento Sconce 205950F Page 1 of 2
INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
For fixtures requiring assembly, please refer to assembly instructions before installation.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Please Note: After installation, extra hardware and accessories may be left due to kits being used on multiple products.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mount Bracket
B Cupped Washer
C Green Ground Screw
D #8 Black Screws (4)
E #10 Screws (8)
F Anchors (8)
G Fixture Assembly
Caution: Be sure power is off at the main breaker box
prior to installation.
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (A) over the
electrical box being sure to hold it plum and level.
If the wall mount bracket has a notch orient bracket
with notch at the bottom. With a pencil, mark the
location of all mounting holes in the wall mount
bracket on the wall behind
IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.
For holes using anchors, place the tapered end of the anchors (F) into the holes and gently tap them flush to the
wall using a light weight hammer.
3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket
into position. Using the 1" #10 screws (E), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
4. Thread the black # 8 screws (D) up through the holes in the top of the wall mount bracket (A). Leave the bottom
screws out for now.
5. Hold the fixture assembly (G) close to the wall mount bracket and using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (C) and cupped
washer (B) to secure a pigtail lead to the bracket.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall.
27718
(continued)
Installation Instructions B270
(Figure 2)
(Figure 3)
Bento Sconce 205950F Page 2 of 2
6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over
the bracket so that the screws in the top of the wall bracket go through the holes in the top of the fixture. Secure
the fixture by threading the remaining black #8 screws (D) up through the holes in the bottom of the fixture and
into the mounting bracket.
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
To Assemble Shade (Figure 2)
Component Parts
H Shade
I Plastic Rivet
1. Carefully unpack the shade (H)
2. Fold flaps (Figure 2) such that the three
holes are aligned
3. Insert plastic rivet (I) through the three holes
and cap on the back
4. Repeat steps 2 & 3 for other side of
shade (H)
To Install Shade (Figure 3)
Component Parts
J Upper Shade Bracket
K Fixture Bracket
L #8 Black Screw (2)
M Lower Shade Bracket
H Shade
1. Install light bulbs (included)
2. Slip shade (H) onto lower shade brackets
(M)
3. Slide upper shade brackets (J ) in place
and fasten with #8 screws (L)
4. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27718
Loading...