Hubbardton Forge 204910 User Manual
Installation Instructions B206
For Staccato Three Light Sconce 20-4910 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
After installation extra hardware and accessories are possible; our kits are used on multiple products and options.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mount Bracket
B Anchors (8)
C #10 Screws (8)
D Fixture Assembly
E #8 x 3/8” Black Screws (2)
F #8 x 3/4” Black Screws (2)
G Green Ground Screw
H Cupped Washer
Caution: Be sure power is off at the main breaker
box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Center the wall mount bracket (A) over the
electrical box being sure to hold it plum and
level. With a pencil, mark the location of all
mounting holes in the wall mount bracket on the
wall behind.
IMPORTANT: Wall mount bracket must be
secured to a solidly mounted electrical box
and/or a framing member in at least two
locations. Do not depend on drywall anchors
alone to support this fixture. If in doubt, contact a
qualified electrician.
Put the wall mount bracket down and drill 1/4"
holes in the locations marked on the wall. For
holes using anchors, place the tapered end of the
anchors (B) into the holes and gently tap them flush to the wall
(Figure 1)
using a light weight hammer.
3. Thread the wires in the electrical box through the center hole in of the wall mount bracket while moving the
bracket into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to overtighten or strip the anchors.
4. Thread the black # 8 screws (E) up through the holes in the top of the wall mount bracket (A). Leave the bottom
screws out for now.
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24451
Installation Instructions B206
For Staccato Three Light Sconce 20-4910 Page 2 of 2
5. Hold the fixture assembly (D) close to the wall mount bracket. Using suitable wire connectors (not provided),
connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (G) and cupped
washer (H) to secure a pigtail lead to the bracket.
6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over
the bracket so that the screws in the top of the wall bracket go through the holes in the top of the fixture. Secure
the fixture by threading the black #8 x 3/4" screws (F) up through the holes in the bottom of the fixture and into
the mounting bracket.
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
To Install Glass
Component Parts
I Socket (3)
J Bulb (3)(included)
K Retaining Ring (3)
L Glass (3)
M Socket Tool
1. Remove retaining ring (K) from socket (I). Retaining ring is
shipped installed.
2. Install light bulb (J). Be careful not to touch bulb with bare hands;
oil from the hands will dramatically reduce bulb life.
3. Slip glass (L) over socket (I) and thread retaining ring (K) onto the
socket (I) using provided socket tool (M).
4. Restore electricity at the main breaker.
(Figure 2)
(Figure 2)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
24451
Loading...