Hubbardton Forge 204901 User Manual

Installation Instructions B199

For Rook Sconce 20-4901 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not
be suitable for all applications. If installing in a non-wood frame application, we recommend
consulting a qualified builder or electrician.

Please Note: After installation extra hardware and accessories are possible; our kits are
used on multiple products and options.

To Mount Fixture to Wall (Figure 1, 2 & 3)

Component Parts

A Crossbar
B 2” Threaded Nipple

C Thin Lock Nut
D Thick Lock Nut
E Ground Screw
F Fixture
G Set Screw

(Figure 1)

To Install

Caution: Be sure power is off at the main breaker box prior to
installation.

1. Carefully unpack the fixture from the carton.

2. Thread the 2” long nipple (B) into the crossbar (A) until there is

approximately 1 ½” protruding out of the crossbar (A) and
secure with thick lock nut (D). Thread thin lock nut (C) onto the
nipple (B) until snug to the back of crossbar (A) (Figure 1).

3. Using two machine screws (not provided) attach crossbar (A) to the

electric box.

replacing a fixture, retain the screws for use with the new fixture.

Note: A new electric box comes with screws. When

4. Run wires through nipple (B) and using suitable wire connectors (not

provided), connect the fixture wires to the supply wires, (white to
white, black to black, bare copper or green to bare copper or green).
Ground the crossbar using the green ground screw (E) to secure a
pigtail lead to the bracket. If the fixture is wired with twin lead lamp
cord, connect the ribbed side to white, and the smooth side to black.

Caution: Make sure wire connectors are twisted on securely and no
bare wires are exposed.

5. Loosen set screw (G) installed into fixture (F).

6. Slip fixture (F) on nipple (B) until firm against wall.

7. Making sure fixture (F) is straight and level; tighten set screw (G) using

supplied wrench until snug.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(Figure 2)

(Figure 3)

(continued)

24349

Installation Instructions B199

For Rook Sconce 20-4901 Page 2 of 2

To Install Glass

Component Parts

H Socket
I Bulb (Included)
J Glass
K Retaining Ring
L Socket Tool
M Spacer

(Figure 4)

1. Install light bulb (I). Be careful not to touch bulb with bare hands; oil

from the hands will dramatically reduce bulb life. Bulb is included.

2. Slip glass (J) and spacer (M) over socket (H). Note orientation of spacer.

Thread retaining ring (K) onto socket (H) using provided socket tool (L).
Be careful not to over tighten.

3. Restore electricity at main breaker.

(Figure 4)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

24349