Hubbardton Forge 204730 User Manual

Installation Instructions B191

For Antasia Wall Sconce 20-4730F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products and
options.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly
B Wall Mount Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (4)
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker box prior
to installation.

1. Center the wall mount bracket (B) over the electrical box

being sure to hold it plum and level. With a pencil, mark
the location of all mounting holes in the wall mount
bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a
solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall
anchors alone to support this fixture. If in doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light weight
hammer.

2. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten
or strip the anchors.

3. Thread the black # 8 screw (E) up through the hole in the top of the wall mount bracket (B). Leave the bottom

screw out for now.

4. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer
(G) to secure a pigtail lead to the bracket.

5. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screws in the top of the wall bracket go through the holes in the top of the fixture. Secure
the fixture by threading the remaining black #8 screws (E) up through the hole in the bottom of the fixture and
into the mounting bracket.

exposed.

Caution: Make sure wire connectors are twisted on securely, and no bare wires are

(Figure 1)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

22865

Installation Instructions B191

For Antasia Wall Sconce 20-4730F Page 2 of 2

To Install Glass (Figure 2)

Component Parts

A Fixture Assembly
H Glass
I ½” Screw (2)
J Bracket

1. Loosen two ½" screws (I) shipped installed

in bracket (J). It is not necessary to remove
them completely.

2. Tilt and position glass (H) so it rests on

fixture assembly (A).

3. Tighten ½" screws (I) into bracket (J)

against glass (H) until snug. Be careful not
to over tighten.

To Install Diffuser

(Figure 3)

(Figure 2)

Component Parts

L Diffuser
M Bulb (2)
N Socket (2)
O ¼” Screw

1. Install light bulb (M). Included with fixture.

2. Remove ¼" screw (O) shipped installed.

3. Install diffuser (L) onto fixture followed by ¼"

screw (O). Tighten screw until snug.

4. Restore electricity at main breaker.

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22865