Installation Instructions B190
For Antasia Sconce 20-4712L & 20-4112R Page 1 of 3
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
Please Note: After installation extra hardware and accessories are possible; our kits are used on multiple products and
options.
To Mount Fixture to Wall with Single Box (Figure 1)
Component Parts
A Crossbar
B Threaded Stud
C Barrel Knob
D Fixture Assembly
E Ground Screw
F Cupped Washer
Caution: Be sure power is off at the main breaker box prior to installation.
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not provided),
fasten the crossbar (A) to the electric box
making sure crossbar is level.
Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use with the new fixture.
3. Thread stud (B) into the appropriate hole in the
crossbar (A). Adjust the stud to proper length to
ensure the fixture will fit snugly to the wall.
4. Hold the fixture assembly (D) close to the wall
and using suitable wire connectors, not
provided, connect fixture wires to supply (white
to white or ribbed and black to black or
smooth). Ground the crossbar (A) using the
green ground screw (E) and cupped washer (F)
to secure a pigtail lead to the bracket. .
Caution: Make sure wire connectors are
twisted on securely, and no bare wire is
exposed.
5. Slide fixture assembly (D) over threaded stud
(B) and push firmly to wall, making sure that no
wires are pinched between fixture back and wall.
Fasten with barrel knob (C). Be sure threaded stud
(B) is fully seated in the barrel knob (C).
6. See instructions following to install glass.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 1)
(continued)
22864
Installation Instructions B190
For Antasia Sconce 20-4712L & 20-4112R Page 2 of 3
To Mount Fixture to Wall with Standard 4” Box
Component Parts
A Crossbar
B Threaded Stud
C Barrel Knob
D Fixture Assembly
E Ground Screw
F Cupped Washer
G Wall Bracket
H 8-32 x 3/8” Screw
Caution: Be sure power is off at the main breaker box prior to installation.
(Figure 2)
1. Carefully unpack the fixture from the carton.
2. Using two machine screws (not
provided), fasten the crossbar (A) to
the electric box making crossbar (A)
is level.
Note: A new electric box comes with
screws. When replacing a fixture,
retain the existing screws for use with
the new fixture
.
3. Thread stud (B) into the appropriate
hole in the crossbar (A). Adjust the
stud to proper length to ensure the
fixture will fit snugly to the wall.
4. Attach wall bracket (G) using 8-32 x
3/8” screw (H). Threaded stud
installed in crossbar will pass through
wall bracket.
5. Hold the fixture assembly (D) close
to the wall and using suitable wire
connectors, not provided, connect
fixture wires to supply (white to
white or ribbed and black to black or
smooth). Ground the crossbar (A)
using the green ground screw (E) and
cupped washer (F) to secure a pigtail
(Figure 2)
lead to the bracket.
Caution: Make sure wire connectors
are twisted on securely, and no bare wire is exposed.
6. Slide fixture assembly (D) over threaded stud (B) and push firmly to wall, making sure that no wires are pinched
between fixture back and wall. Fasten with barrel knob (C). Be sure threaded stud (B) is fully seated in the barrel
knob (C).
7. See instructions following to install glass.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(continued)
22864
Installation Instructions B190
For Antasia Sconce 20-4712L & 20-4112R Page 3 of 3
To Install Glass
Component Parts
I Socket
J Bulb (included)
K Retaining Ring (2)
L Inner Glass
M Outer Glass
N Socket Tool
O Spacer
(Figure 2)
1. Remove retaining rings (K) from socket (I). Retaining rings are shipped
installed.
2. Install light bulb (J). Be careful not to touch bulb with bare hands; oil from
the hands will dramatically reduce bulb life.
3. Slip outer glass (M) and spacer (O) (oriented as shown in Figure 2) over
socket (I). Thread one of the retaining rings onto the socket using socket tool
(N) provided. Note: Flat side of retaining ring should be oriented as shown.
4. Slip inner glass (L) over socket (I).
5. Thread retaining ring (K) onto socket (I) using socket tool (N) until snug
against inner glass (L). Be careful not to over tighten.
Note: Flat side of retaining ring should be oriented as shown.
6. Restore electricity at the main breaker.
(Figure 3)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22864
Loading...