Hubbardton Forge 204670 User Manual

Assembly & Installation Instructions B113

g

For Wall Sconce 20-4670 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Crossbar
B Threaded Stud
C Flat Head Screw
D Barrel Knob
E Fixture Assembly

Caution: Be sure power is off at the main breaker box prior to
installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the crossbar

(B) to the electric box making sure that fixture mounting holes
are level.

Note: A new electric box comes with screws. When replacing a
fixture, retain the existing screws for use with the new fixture.

3. Thread stud (B) into the appropriate hole in the crossbar (A).

Adjust the stud to proper length to ensure the fixture will fit
snugly to the wall.

4. Hold the fixture assembly (E) close to the wall and using suitable

wire connectors (not provided) connect fixture wires to supply
wires (white to white, black to black, and bare copper or green to
bare copper or green).

Caution: Make sure wire connectors are twisted on securely,
and no bare wires are exposed.

5. Slide fixture assembly (E) over threaded stud (B) and push

firmly to wall, making sure that no wires are pinched between
fixture back and wall. Fasten with barrel knob (D). Be sure
threaded stud (B) is fully seated in the barrel knob (D).

6. Thread flat head screw (C) in crossbar (A).

7. See instructions next page to install glass.

8. Install bulb.

9. Restore electricity at main breaker.

e noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19785 Rev B

Assembly & Installation Instructions B113

For Wall Sconce 20-4670 Page 2 of 2

To Install Glass (Figures 2 & 3)

Component Parts

E Fixture Assembly
F Retaining Ring
G Inner Glass
H Knurl Ball (2)
I Studs (2)
J Lamp Socket
K Outer Glass
L Socket Tool
M Flat Washer (2)
N Neoprene Washer (2)
O White Washer

1. Align outer glass (K) over studs (I) protruding from fixture

assembly (E).

2. Slip flat washer (M) and neoprene washer (N) onto

studs (I).

3. Thread knurl ball (H) onto studs (I) until snug against inside

of outer glass (K). Do not over tighten.

4. Place inner glass (G) over lamp socket (J).

5. Slip white washer (O) onto lamp socket (J) until it rests on the

bottom of inner glass (G).

6. Thread retaining ring (F) on to lamp socket using socket tool

provided (L) until it rests on the white washer (O). Do not
over tighten.

(Figure 3)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

(Figure 2)

*

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19785 Rev B