Hubbardton Forge 204650 User Manual

Assembly & Installation Instructions B112

g

For Wall Sconce 20-4650 Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum watta

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all

applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Wall Mounting Bracket
B Anchors (4)
C #10 Screws (4)

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Thread screw (D) in top of wall mounting bracket (A) so it protrudes

through the top.

3. Place the wall mounting bracket (A) over the electrical box using slot

provided being sure to hold it plum and level. With a pencil, mark the
location of all mounting holes in the wall mount bracket on the wall behind.

IMPORTANT: Wall mounting bracket must be secured to a solidly mounted
framing member in at least two locations. Do not depend on drywall anchors
alone to support this fixture. If in doubt, contact a qualified electrician.

Drill 1/4" holes in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (B) into the holes and gently
tap them flush to the wall using a light weight hammer.

4. Thread the wires in the electrical box through the slot in the wall mounting

bracket (A) while moving the bracket into position. Using the 1" #10 screws
(C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.

5. Hold the fixture assembly (E) close to the wall mounting bracket (A) and

using suitable wire connectors (not provided) connect fixture wires to
supply wires (white to white, black to black, and bare copper or green to
bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are
exposed.

6. Carefully tuck all wires behind the fixture assembly (E) and inside the wall mounting bracket (A). Raise the

fixture assembly (E) so that the top hole slips over the screw protruding through the top of the wall mounting
bracket (A). Place the fixture over the bracket so the hole in the bottom matches the threaded hole in the wall
mounting bracket (A). Secure the fixture by threading the #8 black screw (D) through the hole in the fixture
assembly (E) and into the wall mounting bracket (A).

e noted on fixture. Use only recommended bulbs with fixture.

D #8 Screws (2)
E Fixture assembly

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19779 RevA

Assembly and Installation Instructions B112

For Wall Sconce 20-4650 Page 2 of 2

To Install Glass (Figure 2)

Component Parts

F Retaining Ring
G Glass
H Lamp Socket

1. Place glass (G) over lamp socket (H).

2. Thread retaining ring (F) on to lamp socket (H) until it reaches the bottom of the

glass (G).

(Figure 2)

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

19779