Hubbardton Forge 204353 User Manual

Installation Instructions B282

CAUTION: FAILURE TO INSTALL THI S FIXTURE PROPERLY MAY RESULT I N SERIO US PERSO NAL

(Figure 1)

Hobie 3-Light Sconce 20-4353 Page 1 of 2

INJURY OR DEATH AND PROPERTY DAMAGE. We rec o mm e nd installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Fixture Assembly
B Wall Mounting Bracket
C Anchors (4)
D #10 Screws (4)
E #8 Black Screws (4)
F Green Ground Screw
G Cupped Washer

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (B) over the

electrical box being sure to hold it plum and level.
With a pencil, mark the location of all mounting
holes in the wall mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured
to a solidly mounted electrical box and/or a framing
member in at least two locations. Do not depend on
drywall anchors alone to support this fixture. If in
doubt, contact a qualified electrician.

Put the wall mount bracket down and drill 1/4" holes
in the locations marked on the wall. For holes using
anchors, place the tapered end of the anchors (C) into the holes and gently tap them flush to the wall using a light
weight hammer.

3. Using the #10 screws (D), screw the bracket securely to the wall. Be careful not to over-tighten or strip the

anchors.

4. Thread the wires in the electrical box through the center hole in the wall mount bracket.

5. Hold the fixture assembly (A) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth). Ground the
mounting bracket using the green ground screw (F) and cupped washer (G) to secure a pigtail lead to the bracket
and connect all ground wires (bare copper or green to bare copper or green).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture firmly

onto bracket (B) and fasten with #8 black screws (E).

7. Install remaining black screws (E) in bottom of fixture attaching to wall mounting bracket (B).

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28084

Installation Instructions B282

(Figure 2)

Hobie 3-Light Sconce 20-4353 Page 2 of 2

To Install Bulb & Glass Shield (Figure 2)

Component Parts

A Fixture Assembly
H Socket
I Bulb
J Glass Shield

1. Install bulb (I) (included). Be careful not to touch bulb with bare

hands; oil from the hands will dramatically reduce bulb life.

2. Thread glass shield (J) onto socket (H) until snug. Be sure not to over

tighten.

3. Complete steps 1 & 2 for remaining sockets.

4. Restore electricity at main breaker.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

*

Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

28084