Hubbardton Forge 204301 User Manual

Installation Instructions B200

For Constellation Sconce 20-4301 Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

After installation extra hardware and accessories are possible; our kits are used on multiple products and options.

To Mount Fixture to Wall with Single Box (Figure 1)

Component Parts

A Crossbar
B Threaded Stud
C Barrel Knob
D Fixture Assembly
E Ground Screw
F Cupped Washer

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the

crossbar (A) to the electric box making sure crossbar
is level.

Note: A new electric box comes with screws. When
replacing a fixture, retain the existing screws for use
with the new fixture

3. Thread stud (B) into the appropriate hole in the

crossbar (A). Adjust the stud to proper length to
ensure the fixture will fit snugly to the wall.

4. Hold the fixture assembly (D) close to the wall and

using suitable wire connectors (not provided)
connect fixture wires to supply (white to white or
ribbed and black to black or smooth). Ground the
crossbar (A) using the green ground screw (E) and
cupped washer (F) to secure a pigtail lead to the
bracket. .

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

5. Slide fixture assembly (D) over threaded stud (B)

and push firmly to wall, making sure that no wires
are pinched between fixture back and wall. Fasten
with barrel knob (C). Be sure threaded stud (B) is fully seated in the barrel knob (C).

6. See instructions following to install glass.

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

.

(Figure 1)

(continued)

24399

Installation Instructions B200

For Constellation Sconce 20-4301 Page 2 of 3

To Mount Fixture to Wall with Standard 4" Box (Figure 2)

Component Parts

A Crossbar
B Threaded Stud
C Barrel Knob
D Fixture Assembly
E Ground Screw
G Wall Bracket
H 8-32 x 3/8” Screw

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided),

fasten the crossbar (A) to the electric box
making sure crossbar is level.

Note: A new electric box comes with
screws. When replacing a fixture, retain the
existing screws for use with the new fixture

3. Thread stud (B) into the appropriate hole in

the crossbar (A). Adjust the stud to proper
length to ensure the fixture will fit snugly to
the wall.

4. Attach wall bracket (G) using 8-32 x 3/8"

screw (H). Threaded stud installed in
crossbar will pass through wall bracket.

5. Hold the fixture assembly (D) close to the

wall and using suitable wire connectors, not
provided, connect fixture wires to supply
(white to white or ribbed and black to black
or smooth). Ground the crossbar (A) using
the green ground screw (E) to secure a
pigtail lead to the bracket.

Caution: Make sure wire connectors are twisted
on securely, and no bare wire is exposed.

6. Slide fixture assembly (D) over threaded stud (B) and push firmly to wall, making sure that no wires are pinched

between fixture back and wall. Fasten with barrel knob (C). Be sure threaded stud (B) is fully seated in the barrel
knob (C).

7. See instructions following to install glass.

.

(Figure 2)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

24399