Hubbardton Forge 204265 User Manual

Installation Instructions B138

For New Town Sconces 20-4255, 204265 & 204265F Page 1 of 2

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

For fixtures requiring assembly, please refer to assembly instructions before installation.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

To Mount Fixture to Wall (Figure 1)

Component Parts

A Wall Mount Bracket
B Anchors
C #10 Screws
D Fixture Assembly
E #8 Black Screws
F Green Ground Screw
G Cupped Washer
H Set Screw (2)

Caution: Be sure power is off at the main breaker box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Center the wall mount bracket (A) over the electrical box being sure to hold it

plum and level. If the wall mount bracket has a notch orient bracket with notch at the bottom. With a pencil, mark
the location of all mounting holes in the wall mount bracket on the wall behind.

IMPORTANT: Wall mount bracket must be secured to a solidly mounted electrical box and/or a framing member
in at least two locations. Do not depend on drywall anchors alone to support this fixture. If in doubt, contact a
qualified electrician.

Put the wall mount bracket down and drill 1/4" holes in the locations marked on the wall. For holes using anchors,
place the tapered end of the anchors (B) into the holes and gently tap them flush to the wall using a light weight
hammer.

3. Thread the wires in the electrical box through the center hole in the wall mount bracket while moving the bracket

into position. Using the 1" #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.

4. Thread the set screws (H) through the holes in the top of the wall mount bracket (A) so they protrude

approximately 1/4". Leave the bottom screws out for now.

5. Hold the fixture assembly (D) close to the wall mount bracket and using suitable wire connectors (not provided),

connect fixture wires to supply wires (white to white or ribbed and black to black or smooth, and bare copper or
green to bare copper or green). Ground the mounting bracket using the green ground screw (F) and cupped washer
(G) to secure a pigtail lead to the bracket.

6. Carefully tuck all wires behind the fixture assembly and inside the wall mount bracket and place the fixture over

the bracket so that the screws in the top of the wall bracket go through the holes in the top of the fixture. Secure
the fixture by threading the black #8 screws (E) up through the holes in the bottom of the fixture and into the
mounting bracket (A).

Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21177

Installation Instructions B138

For New Town Sconces 20-4255, 204265 & 204265F Page 2 of 2

To Install Glass (Figure 2)

Component Parts

D Fixture Assembly
I Screw (4)
J Glass Ring (4)
K Glass (4)

1. Install light bulbs (fluorescent bulb provided with fixture).

2. Slip glass ring (J) over glass (K) making sure the counter sunk side

of hole is facing up. Install glass (K) aligning glass ring (J) hole
with threaded hole in fixture assembly (D).

3. Install screw (I) to attach glass ring (J) to fixture assembly (D).

4. Restore electricity at the main breaker.

This illustration represents a typical
fixture and may not match every style.

If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!

* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.

(Figure 2)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

21177