Hubbardton Forge 203035 User Manual
Assembly & Installation Instructions B269
Flora Sconce 20-3035 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.
After installation, extra hardware and accessories may be left due to kits being used on multiple products.
To Mount Fixture to Wall (Figure 1)
Component Parts
A Wall Mounting Bracket
B Anchors (3)
C #10 Screws (3)
D Electric Box Cover
(for 4” Outlet box)
Caution: Be sure power is off at the main breaker box prior to
installation.
1. Carefully unpack the fixture from the carton.
2. Place the wall mounting bracket (A) over the electrical box
using one of the wiring holes provided being sure to hold it
plum and level (square openings should be towards
bottom). If using a single gang outlet box electric box,
cover (D) is not needed. Remove a #8 black screw (E)
from electric box cover (D) and save for later use.
Determine which electric box cover (D) location works the
best and attach to wall mounting bracket (A). With a
pencil, mark the location of all mounting holes in the wall
mount bracket on the wall behind.
IMPORTANT: Wall mounting bracket must be secured to a
solidly mounted to a framing member in at least two locations.
Do not depend on drywall anchors alone to support this fixture.
If in doubt, contact a qualified electrician.
3. Drill 1/4" holes in the locations marked on the wall. For holes using anchors, place the tapered end of the anchors
(B) into the holes and gently tap them flush to the wall using a light weight hammer.
4. Thread the wires in the electrical box through the hole in the wall mounting bracket (A) while moving the bracket
into position. Using the #10 screws (C), screw the bracket securely to the wall. Be careful not to over-tighten or
strip the anchors.
5. Hold the fixture assembly (F) close to the wall mounting bracket (A) and using suitable wire connectors (not
provided) connect fixture wires to supply wires (white to white or ribbed, black to black or smooth, and bare
copper or green to bare copper or green). Using ground screw (G) and cupped washer (H) run a pigtail lead to the
electrical box. Connect all ground wires (green or bare copper.)
Caution: Make sure wire connectors are twisted on securely, and no bare wires are exposed.
6. Carefully tuck all wires behind the fixture (F) and inside the wall mounting bracket (A) and place the fixture over
the bracket (A). Secure the fixture by threading the black screws (E) through the holes in the fixture (F) and into
the wall mounting bracket (A).
7. See following instructions to install glass.
E #8 Black Screws (3)
F Fixture Assembly
G Ground Screw
H Cupped Washer
(Figure 1)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27571
Assembly & Installation Instructions B269
Flora Sconce 20-3035 Page 2 of 2
To Install Single Glass Option
Component Parts
I Socket
J Bulb
K Glass
L Retaining Ring
M Retaining Ring Tool
1. Remove retaining ring (L) from socket (I). Retaining ring ships installed.
2. Install light bulb (J). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
Note: The bulb included is based on our design preference; see the fixtures
wattage sticker for Max wattage information.
3. Slip glass (K) over socket (I) and tighten retaining ring (L) with retaining ring
tool (M). Be sure not to over tighten.
4. Restore electricity at main breaker.
To Install Double Glass Option
(Figure 2)
(Figure 3)
Component Parts
I Socket
J Bulb
K Glass
L Retaining Ring
M Retaining Ring Tool
N Inner Glass
1. Remove retaining ring (L) from socket (I). Retaining ring ships installed.
2. Install light bulb (J). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
Note: The bulb included is based on our design preference; see the fixtures
wattage sticker for Max wattage information.
3. Place inner glass (N) into glass (K) and slip both over socket (I) and tighten
retaining ring (L) with retaining ring tool (M). Be sure not to over tighten.
4. Restore electricity at main breaker.
If you need further assistance, or find that you are missing any parts, please contact the
dealer from which you purchased this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation,
lamping or use of this fixture.
(Figure 2)
(Figure 3)
Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735
27571
Loading...