Hubbardton Forge 203030 User Manual

Installation Instructions B210

Flora Sconce 20-3030 Page 1 of 3

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Please Note: This fixture is designed to be mounted on a standard wall surface and may not be suitable for all
applications. If installing in a non-wood frame application, we recommend consulting a qualified builder or electrician.

After installation extra hardware and accessories are possible; our kits are used on multiple products and options.

To Mount Fixture to Wall with Single Box (Figure 1)

Component Parts

A Crossbar
B Nipple
C Threaded Cap
D Fixture Assembly
E Ground Screw
F Lock Nut

Caution: Be sure power is off at the main breaker box
prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided), fasten the

crossbar (A) to the electric box making sure crossbar
is level.

Note: A new electric box comes with screws. When
replacing a fixture, retain the existing screws for use
with the new fixture

3. Thread the nipple (B) into the crossbar (A) and secure

with lock nut (F). Adjust the nipple to proper length
to ensure the fixture will fit snugly to the wall.

4. Ground the crossbar (A) by securing a pigtail lead

around ground screw (E).

5. Hold the fixture assembly (D) close to the wall and

using suitable wire connectors (not provided) connect
fixture wires and pigtail leads to supply wires (white
to white or ribbed, black to black or smooth and green
to green or bare).

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

6. Carefully tuck all wires behind the fixture, place

fixture firmly against the wall and fasten with
threaded cap (C).

7. See instructions following to install wall plate.

.

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

24581RevA

Installation Instructions B210

Flora Sconce 20-3030 Page 2 of 3

To Mount Fixture to Wall with Standard 4" Box (Figure 2)

Component Parts

A Crossbar
B Nipple
C Threaded Cap
D Fixture Assembly
E Ground Screw
F Lock Nut
G Wall Plate
H Cupped Washer
I Ground Screw

Caution: Be sure power is off at the main breaker
box prior to installation.

1. Carefully unpack the fixture from the carton.

2. Using two machine screws (not provided),

fasten the crossbar (A) to the electric box
making sure crossbar is level.

Note: A new electric box comes with screws.
When replacing a fixture, retain the existing
screws for use with the new fixture

3. Thread the nipple (B) into the crossbar (A).

Adjust the nipple to proper length to ensure
the fixture will fit snugly to the wall.

4. Ground the crossbar (A) by securing a pigtail

lead around ground screw (E).

5. Orient the wall plate (G) so that the bent tab is

at the top and bent away from the wall and slip onto
nipple (B). The tab will fit into the back of the
fixture to facilitate alignment.

6. Run a pigtail lead using ground screw (I) and cupped washer (H).

7. Thread the pigtail lead and fixture wires through the large diameter hole at the bottom of the wall plate (G).

8. Hold the fixture assembly (D) close to the wall and using suitable wire connectors, not provided, connect fixture

wires and pigtail leads to supply wires (white to white or ribbed, black to black or smooth and green to green or
bare).

Caution: Make sure wire connectors are twisted on securely, and no bare wire is exposed.

9. Secure nipple (B) and wall plate (G) with lock nut (F).

10. Place fixture firmly against the wall and fasten with threaded cap (C).

11. See instructions following to install glass.

.

(Figure 2)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
154 Route 30 South, Castleton, Vermont 05735

24581RevA