Hubbardton Forge 19453010 User Manual
Assembly & Installation Instructions A122
For Compass Chandelier 19-453010 & 19-453610 Page 1 of 3 _
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Install the Canopy (Figure 1)
Component Parts
A Crossbar
B Threaded Nipple
C Lag Screw (2)
Caution: Be sure power is off at the main breaker box prior to installation.
Caution: This fixture must be supported independently of an outlet box. Crossbar is
designed to fit in the bottom of a standard metal 4” octagonal outlet box.
D Lock Nut
E Canopy
F Loop Collar
G Threaded Loop
H Chain
I Fixture Loop
1. Drill two holes through the back of the outlet box and using two lag screws (C) attach
cross bar (A) to a structural member in the ceiling, centering the crossbar in the outlet
box. We've supplied lag screws with your fixture; however, different materials and/or
construction methods may require different fasteners. If in doubt, contact a qualified
electrician.
2. Thread the nipple (B) into the crossbar (A).
3. Thread lock nut (D) and threaded loop (G) onto nipple, then place canopy (E) over
threaded loop and adjust nipple length to ensure a snug canopy fit. Once the length is
determined, set the canopy aside and lock nipple position by tightening the locknut
(D) against the crossbar (A).
4. Attach one end of the chain (H) to the fixture loop (I).
5. Attach the other end of the chain to the threaded loop (F) and thread the fixture wires
through every other link of the chain (H) and up through the threaded loop (G) and
nipple (B) into the outlet box.
6. Using suitable wire connectors (not provided), connect fixture wires to supply wires
(white or ribbed side of fixture cord to white supply, black or smooth side of fixture
cord to black supply, and bare copper to bare copper or green supply). Push wires
back into outlet box.
Caution: Make sure wire connectors are twisted on securely, and no bare wire is
exposed.
7. Slide the canopy up the chain and over the threaded loop (G), securing with loop
collar (F). Make sure no wires are pinched between the canopy (E) and the ceiling or
crossbar (A).
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19895 Rev A
(Figure 1)
(Figure 1)
(continued)
Assembly & Installation Instructions A122
For Compass Chandelier 19-453010 & 19-453610 Page 2 of 3 _
Install the Threaded Rods
Component Parts
J Plug
K Hex Nut (4)
L Loop Assembly
M Threaded Rod (4)
1. Slip bent end of threaded rod (M) through holes in loop assembly (L).
2. Thread hex nut (K) onto threaded rod (M) until bottomed out and snug.
3. Lower threaded rod (M) until hex nut (K) sits flat inside loop assembly (L).
4. Install plug (J) in holes of loop assembly (L) to cover hex nut (K).
(Figure 2)
To Install Glass Frame and Glass
Component Parts
M Threaded Rod (4)
N Glass
O Tab
P Threaded Ball (4)
Q Glass Frame
(Figure 3)
1. Slip tabs on glass frame (Q) onto three threaded rods (M)
and attach with threaded ball (P).
2. Slip glass (N) into glass frame (Q) so it rests below the
three tabs.
3. Slip tab (O) onto last threaded rod (M) and slide onto glass
frame (Q).
4. Thread threaded ball (P) onto threaded rod (M).
5. Install light bulbs (not provided).
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 2)
(Figure 3)
(continued)
19895 Rev A
Loading...