Hubbardton Forge 19453000 User Manual
Assembly & Installation Instructions A121
For Compass Chandelier 19-453000 & 19-453600 Page 1 of 3 _
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Install the Canopy (Figure 1)
Component Parts
A Hex Nut
B Lock Washer
C Hang Plate
D Spacer
E Threaded Nipple
Caution: Be sure power is off at the main breaker box prior to installation.
Caution: This fixture must be supported independently of an outlet box.
F Coupling
G Crossbar
H 1/4-20 Hex Nut (2)
I Lag Screw (4)
J Canopy
K Cover Plate
L Canopy Ring
M Socket Assembly
1. Using at least two lag screws (I) attach cross bar (G) to a structural member
in the ceiling, centering the crossbar over the outlet box. We've supplied lag
screws with your fixture; however, different materials and/or construction
methods may require different fasteners. If in doubt, contact a qualified
electrician. Do not
attach crossbar directly to outlet box.
2. Slip canopy ring (L), large diameter first, over threaded nipple (E) and
thread on and over coupling (F) followed by cover plate (K) and canopy (J)
coming to rest on socket assembly (M).
3. Slip spacer (D) onto threaded nipple (E) so it rests on top of coupling (F).
4. Slip hang plate (C) onto threaded nipple (E) so it rests on top of spacer (D).
5. Slip lock washer (B) over threaded nipple (E). Thread hex nut onto threaded
nipple (E) and tighten against lock washer (B) and hang plate (C).
6. Push hang plate (C) at top of fixture up into electrical box, past the crossbar
(G). Turn the hanger plate and drop the screws into the larger inner holes in
the crossbar (G). Make sure no wires are pinched. Secure using two 1/4-20
nuts (H).
7. Using suitable wire connectors (not provided), connect fixture wires to
supply wires (white or ribbed side of fixture cord to white supply, black or
smooth side of fixture cord to black supply, and bare copper to bare copper
or green supply). Push wires back into outlet box. Caution: Make sure wire
connectors are twisted on securely, and no bare wire is exposed.
(Figure 1)
(Figure 1)
(continued)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
19894 Rev A
Assembly & Installation Instructions A121
For Compass Chandelier 19-453000 & 19-453600 Page 2 of 3 _
Install the Threaded Rods
Component Parts
J Canopy
K Cover Plate
L Canopy Ring
N Threaded Rod (4)
O Hex Nut (4)
1. Slip bent end of threaded rod (N) through slots in canopy (J).
2. Thread hex nut (O) onto threaded rod (N) until snug against inside
of canopy (J).
3. Slide fixture canopy (J) and cover plate (K) against ceiling, and
secure with canopy ring (L). Be sure cover plate is aligned square
with canopy.
(Figure 2)
To Install Glass Frame and Glass
Component Parts
N Threaded Rod (4)
P Glass
Q Tab
R Threaded Ball (4)
S Glass Frame
(Figure 3)
1. Slip tabs on glass frame (S) onto three
threaded rods (N) and attach with threaded
ball (R).
2. Slip glass (P) into glass frame (S) so it rests
below the three tabs.
3. Slip tab (Q) onto last threaded rod (N) and
slide onto glass frame (S).
4. Thread threaded ball (R) onto threaded
rod (N).
5. Install light bulbs (not provided).
(Figure 2)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
(Figure 3)
(continued)
19894 Rev A
Loading...