Hubbardton Forge 19415612HG User Manual

Assembly & Installation Instructions A238

For Ribbon Chandelier 19-415612HG Page 1 of 3 _

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

Install the Canopy (Figure 1)

Component Parts

A Crossbar
B Threaded Nipple
C Lag Screw (2)
D Lock Nut

Caution: Be sure power is off at the main breaker box prior to installation.
Caution: This fixture must be supported independently of an outlet

box. Crossbar is designed to fit in the bottom of a standard metal 4”
octagonal outlet box.

E Canopy
F Loop Collar
G Threaded Loop
H Chain

I Fixture Loop
J Ground Screw
K Cupped Washer
L Hex Nut

(Figure 1)

1. Drill two holes through the back of the outlet box and using

two lag screws (C) attach cross bar (A) to a structural
member in the ceiling, centering the crossbar in the outlet
box. We've supplied lag screws with your fixture; however,
different materials and/or construction methods may require
different fasteners. If in doubt, contact a qualified
electrician.

2. Thread the nipple (B) into the crossbar (A).

3. Thread lock nut (D) and threaded loop (G) onto nipple, then

place canopy (E) over threaded loop and adjust nipple
length to ensure a snug canopy fit. Once the length is
determined, set the canopy aside and lock nipple position
by tightening the locknut (D) against the crossbar (A).

4. Attach one end of the chain (H) to the fixture loop (I).

5. Attach the other end of the chain to the threaded loop (G)

and thread the fixture wires through every other link of the
chain (H) and up through the threaded loop (G) and nipple
(B) into the outlet box.

6. Using suitable wire connectors (not provided), connect

fixture wires to supply wires (white or ribbed side of fixture
cord to white supply, black or smooth side of fixture cord to
black supply, and bare copper to bare copper or green
supply). Ground the crossbar (A) using the ground screw
(J), cupped washer (K) and hex nut (L) to secure a pigtail
lead to the crossbar. Push wires back into outlet box.

Caution: Make sure wire connectors are twisted on
securely, and no bare wire is exposed.

7. Slide the canopy up the chain and over the threaded loop (G), securing

with loop collar (F). Make sure no wires are pinched between the canopy
(E) and the ceiling or crossbar (A).

(Figure 1)

(continued)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

24409

Assembly & Installation Instructions A238

For Ribbon Chandelier 19-415612HG Page 2 of 3 _

To Install Single Glass Option

Component Parts

I Glass (12)
J Socket (12)
K Bulb (Included) (12)
L Spacer (24)
M Retaining Ring (12)

1. Remove retaining rings (M) from sockets (J). Retaining rings are

shipped installed on sockets.

2. Install light bulbs (K). Be careful not to touch bulb with bare

hands; oil from the hands will dramatically reduce bulb life.

3. Slip glass (I) and spacers (L) over socket (J). Note orientation of

spacers.

4. Thread retaining ring (M) onto socket (J) until snug against spacer

(L). Be careful not to over tighten. Repeat steps 2 thru 4 for all
twelve arms.

5. Restore electricity at main breaker.

(Figure 2)

(Figure 2)

Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

(continued)

24409