Assembly & Installation Instructions A214
Antimeny Single Pendant 18-761 Page 1 of 2
CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL
INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.
This product must be installed in accordance with applicable installation code(s), by a person familiar with the
construction and operation of the product and the hazards involved.*
Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.
Please Note: After installation extra hardware and accessories are possible due to our kits are used on multiple products
and options.
To Complete Fixture Assembly (Figures 1 & 2)
Component Parts
A Fixture Pipe
B Canopy
C Crossbar
D Ground Screw
E Threaded Stud (2)
Caution: Be sure power is off at the main breaker box prior to installation.
1. Thread the wires from the fixture pipe (A) into and through the canopy pipe (G) up through
the canopy (B).
2. Unscrew the clutch (I) from the canopy pipe (G); slide it across the wires and onto the
fixture pipe (A). Follow this with the plastic clutch sleeve (H), oriented so the tapered end of
the clutch sleeve nests in the clutch.
3. Slide the canopy pipe (G) as far as necessary to give you the total length of the fixture which
you desire. Be careful not to scratch the pipe surfaces and to pull excess wire up through the
canopy pipe (G). Screw clutch (I) onto canopy pipe (G). There must be a minimum 1-1/2"
of inner pipe inside the outer pipe. Hand-tighten the clutch to temporarily hold this
adjustment. The clutch is not securely fastened at this point; do not depend on it to hold the
fixture. Important: To ensure full connection strength, be sure the tapered end of the plastic
clutch sleeve is oriented toward the clutch when assembled and securely tighten set screw
(Figure 2).
4. Thread studs (E) through appropriate holes in crossbar (C) to match holes in canopy (B).
5. Using two machine screws (not provided), fasten the crossbar (C) to the electric box.
Note: A new electric box comes with screws. When replacing a fixture, retain the existing
screws for use with the new fixture.
6. Using suitable wire connectors (not provided) connect fixture
wires to supply (white to white or ribbed and black to black or
smooth). Connect all ground wires to green ground screw (D).
Caution: Make sure wire connectors are twisted on securely,
and no bare wire is exposed.
7. Slide canopy (B) over threaded studs (E) and push firmly to
ceiling, making sure that no wires are pinched between fixture
canopy and ceiling. Fasten with barrel knobs (F). Be sure studs
are fully seated in the barrel knobs.
8. Once the fixture is fastened to the ceiling, tighten the set screw
(J) in clutch (I) firmly with hex wrench provided. Only after the
set screw (J) is tight should you install the glass.
9. Refer instructions following to install glass. (continued)
F Barrel Knob (2)
G Canopy Pipe (2)
H Plastic Clutch Sleeve (2)
I Clutch (2)
J Set Screw (2)
(Figure 1)
(Figure 2)
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22863
Assembly & Installation Instructions A214
Antimeny Single Pendant 18-761 Page 2 of 2
To Assemble Glass & Spider (Figure 3)
Component Parts
K Glass
L Spider
M Barrels
1. Place spider (L) into glass (K).
2. Secure glass to spider by threading barrels (M) through holes in glass and onto
legs of spider. Start all three barrels before tightening any individually.
To Install Glass
Component Parts
N Glass Assembly
O Socket
P Retaining Ring
Q Bulb (Included)
R Bulb Shield
(Figure 4)
(Figure 3)
1. Install light bulb (Q). Be careful not to touch bulb with bare hands; oil from the
hands will dramatically reduce bulb life.
2. Slip glass assembly (N) over socket (O) and thread retaining ring (P) onto socket
until snug.
3. Thread bulb shield (R) onto socket (O) (be careful not to over tighten). Future bulb
changes may be accomplished by snapping glass portion of barrier on and off
rather than unthreading the holder.
4. Restore electricity at main breaker.
(Figure 4)
If you need further assistance, or find that you are missing any parts, please contact the dealer from which you purchased
this product. We hope you enjoy your fixture!
* Hubbardton Forge will not be liable for injury or damage caused by improper installation, lamping or use of this fixture.
Hand-Forged, Vermont-Made Lighting and Accessories
P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735
22863
Loading...